1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Texasrocker are you out there? Another cap question.
jerryhawthorne
Phorum Expert
*****
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
#1

11-12-2011, 10:52 PM
I know you have some reference which is better than that posted on the work bench. Another one of those dang philco bakelite stuff caps I can't find a reference to. Its a 3903AB. I know it has one cap in it, can you tell me what it is? Add another as an edit, the 3903T. Single cap, what is it? One more, not on the bench list, a 7025D. Any help appreciated.

Thanks Jerry
A friend in need is a pest!  Bill Slee ca 1970.
Find
Bradley Rush
RadioMonkey
***
Posts: 220
Threads: 56
Joined: Oct 2011
City: Lompoc CA
#2

11-13-2011, 02:11 AM
3903AB= 3903OSU
ONE ,01 UF 600V
Find
Bradley Rush
RadioMonkey
***
Posts: 220
Threads: 56
Joined: Oct 2011
City: Lompoc CA
#3

11-13-2011, 02:13 AM
3903T = 39030SU
ONE .01 UF 600V
Find
Bradley Rush
RadioMonkey
***
Posts: 220
Threads: 56
Joined: Oct 2011
City: Lompoc CA
#4

11-13-2011, 02:15 AM
SERVICE BULLETIN NO. 289
Is where I found the info
Find
Bradley Rush
RadioMonkey
***
Posts: 220
Threads: 56
Joined: Oct 2011
City: Lompoc CA
#5

11-13-2011, 02:19 AM
no 7025D

but
7625D
3-4 .015 uf 600v
1-5 .006 uf 600v
Find
jerryhawthorne
Phorum Expert
*****
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
#6

11-13-2011, 04:56 PM
Thanks TROG, got me off and running again. Will have to check on the 7025D, perhaps I missread it and it was a 7625D.

Jerry
A friend in need is a pest!  Bill Slee ca 1970.
Find
Texasrocker
Phorum Expert
*****
Posts: 909
Threads: 117
Joined: Jun 2007
#7

11-16-2011, 01:41 PM
Sorry for the delay getting here Jerry. Been real busy lately. Looks like you have the specific caps info you needed now. Always glad to help if I can, you can also pm me, as I'm not on the forums each and every day.
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM

[-]
Who's Online
There are currently 6157 online users. [Complete List]
» 2 Member(s) | 6155 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration