Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Antenna, Cowl
#1

Icon_confused: Anyone have an ad/photo/lit that shows a side cowl mounted antenna offered in 1933 or earlier.

Yrs back i restored a 1933 Chry. Phaeton that had 2 factory holes in the bodies structural wood that would be perfect for an antenna mount. At the time i talked to another guy restoring the same car and his had the same 2 holes. I know the closed cars had the roof/chicken wire antenna and there were the under running board but did some of the open cars get a side cowl.

Maybe the Antenna shown on this car
http://jamesmeltonmusicalcareerantiqueca...erial.html
is factory. Photo was taken in the 50s.

Barry
keating@q.com
801 971 1934
#2

The wip type antenna came out in the late 30's offen the running board antenna was used on open cars and steel top bodies, 1937 Buick used this type of antenna, 33-35
Ford open cars used the rear mounted spare tire as an antenna on open cars, 37 Cord ,being front wheel drive, had an antenna where the drive shaft would go on rear wheel drive cars. I have in structions from the early 30's on installing antenna in the roof of open cars! Reception would not be too good with the top down!
#3

While looking for info i ran accross this 1919 Antenna
http://www.oldmagazinearticles.com/First_Car_Radio_pdf
but still nothing on a 1933 cowl mount
#4

Could your holes in the cowl be for a side mount spare? ,The earlest car I know with the wipe antenna is the 37 Ford ,mounted in the center of the just above the windshield ,it was small and required an antenna transformer,that was mounted inside under the head liner above the windshield




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM
Zenith H725
Ed; One material that I have seen, but never tried for this was material for making exhaust gaskets, it's similar to ...Arran — 11:42 PM
Zenith H725
I just remembered, I have some hi temp silicone rubber material which could do the trick. Or a piece of FR4 laminate. Th...EdHolland — 08:39 PM
Zenith H725
The PSU filter cap arrived today (thank you USPS!) so I will work on that later. Meanwhile, I have the dial, speaker...EdHolland — 06:42 PM
Philco 610B oscillator wiring
Thanks Terry. After checking my notes I think I recorded about -10v at the 6A7 G4/control grid. The screen grid (G3 &...Tubester — 05:59 PM

[-]
Who's Online
There are currently 1540 online users. [Complete List]
» 1 Member(s) | 1539 Guest(s)
Avatar

>