Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 97
#1

I have recently aquired a 1935 philco 97 in great condition unfortunatly though the pilot lamp set up is not all there anyone knowanythig about this radio
the dial has a square at the top which must light up I presume when turned on ?

thanks
#2

The 97 is a fairly uncommon set. Not sure what you mean about the pilot light set up not being all there.

The "window" is a shadow meter, it gives a visual indication for more precise tuning. If it doesn't light up, the bulb is probably not working.
#3

hank you for the info regardingthe shadow meter I just cant understand after looking at the pilot light set up how that works or should light up by bettr tuning
#4

nzbhoy Wrote:hank you for the info regardingthe shadow meter I just cant understand after looking at the pilot light set up how that works or should light up by bettr tuning
This will explain about Philco shadow meters.

http://philcorepairbench.com/tips/svctip01.htm

Larry
#5

There are four lights there. The highest one is behind the shadow meter. It illuminates a vane inside the meter. As you tune in a station, the shadow cast by the vane becomes narrower. At it's narrowest point the station is tuned in at it's maximum.

The other 3 lights illuminate the 3 different bands on the dial. As you switch the band selector control, a different light illuminates the band selected.

I restored a model 97 last summer. Please send some pics of yours to this phorum, I am sure that many of us would love to see it. Should you have any more questions, Philco Radio.com (this site) and the Philco Repair Bench sites are the places to ask, as they are literally the best repositories of Philco knowledge anywhere!

ALSO: If you like Philco Radios, Ron's book Philco Radio 1928-1942 is the best Philco reference out there, and Chuck's website Philco Repair Bench has a schematic and technical information service that will provide you with excellent quality information on your set.




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
My Philco 37-116 Restore
Hello MrFixr55, Thank you for taking the time to explain. I measured 50 volts where you say. Today the 370 volts at ...dconant — 12:51 PM
462ron
Oh that sucks. It’s something easily overlooked. Hopefully it’s nothing more than a resistor! Ron462ron — 08:08 AM
Philco 46-480 Electronic Restoration
Just confirmed that you are correct. It’s the function generator. I connected the signal output probe to one of the inpu...jrblasde — 07:52 AM
Philco 46-480 Electronic Restoration
Ouch, you may be right. Yes, it is solid state. It’s the signal output of my oscilloscope. May be time to crack that ...jrblasde — 07:27 AM
462ron
If you didn’t put a DC blocking cap between the signal generator probe and the plate of the 1st IF it’s possible you ble...462ron — 07:07 AM
My Philco 37-116 Restore
Hi DConnant, The reason why C127 is isolated from ground is because sets of this vintage did not have the center tap...MrFixr55 — 01:07 AM
Philco 46-480 Electronic Restoration
The shield is on the 6H6. It was, in fact, a missing jumper to connect the main chassis ground to the RF chassis grou...jrblasde — 10:58 PM
Zenith H725
When dealing with noise on power lines, time to get my Jackery 240 out. Talk about clean can hold a portable am radio ne...David — 08:52 PM
Zenith H725
Arran - I bet you're right probably vinyl, there was no rubber smell when desoldering it, which you often get with the o...EdHolland — 08:23 PM
Zenith H725
Ed; It was very likely vinyl covered wire given the vintage of the set, there was some rubber/gutta percha wire used ...Arran — 06:34 PM

[-]
Who's Online
There are currently 1417 online users. [Complete List]
» 1 Member(s) | 1416 Guest(s)
Avatar

>