Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Introduction and questions regarding a Philco 112A
#1

Hello,

My name is Jim, and I am a total newbie when it comes to radios. We were fortunate enough to get a Philco 112A at an auction. Now then, on the plate on the back of the radio, it says it was made in Toronto, Ontario. Thus, this might explain the "A"? I've only found the Philco 112 Lowboy on Ron's site, and that fits it to a tee. I believe it may be one of Norman Bel Geddes designs, but, I don't know for sure. To make a long story shorter, the radio stopped working. Tubes seem to still light, etc, but, no audio at all. I see that there is two configurations for the tube layout. I don't know where to find the
the serial number. Within the 2 configurations it shows what the layout is
"above serial number 174,001" and the other shows the layout "below serial number 174,001"

I don't know where to start, so, I turn to you good folks. I understand that we are dealing with high voltages, etc, so, I won't go digging around without knowing exactly what to do.

So, what should I start looking for?

Thanks for any assistance; this is a great Phorum!!
I am looking forward to learning all about these radios!

All the best,

Jim
#2

Hi and welcome! Icon_smile

The "A" does, indeed, signify the Canadian/Canadien version. The only difference is the values of the filter caps and the power transformer rated for 25 Hz power mains. It will work fine on 60Hz.

The Model 112 is a very nice set and a good performer.

DO NOT plug the set in any more until it can be fully restored. Permanent damage to irreplaceable components can result.

If you are not electronically inclined, I would suggest finding an antique radio club in your vicinity to help you. Many clubs have members who offer restoration services. To find a club near you, see the Radio Club Listing here: http://www.antiqueradio.com/clublist.html

Good Luck and let us know how it goes. Icon_smile



Alternatively, Ron Ramirez here can offer his services as well (shameless plug). See here: <!-- m --><a class="postlink" href="http://www.philcoradio.com/rre/services.htm">http://www.philcoradio.com/rre/services.htm</a><!-- m -->
#3

For sure,

I don't want to do any damage to it. I received an email from
"theoldradiofixerupperguy" and he pointed me to a place just a few miles away from me that does professional repairs and restoration.
(Gotta love the internet!!) Icon_biggrin

I guess I just wanted to find out if there is anything I could change myself, before getting into major costs...

Thanks again for your assistance!

Jim
#4

Hello,

Just wondering where I look for the serial number. I looked on the plate on the back, but it only shows the model number, and where it was made.

I would appreciate any assistance with this.

Thanks so much!

Jim
#5

Serial number may be stamed into the chassis near the rear edge or may be on the bottom plate of the chassis, I beleive. All early Philcos were made in Philadelphia. See Philco History here on this site.
#6

Thanks Chuck,

I'll look underneath the chassis when I get home tonight.

Jim




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently 2217 online users. [Complete List]
» 2 Member(s) | 2215 Guest(s)
AvatarAvatar

>