Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Volume Control Cleaning Tool
#1

Some while ago I ran across a web site where an apparently older gentleman sold some pretty nifty aids and tools. I do remember he had a tool that apparently screwed onto the volume control shaft, allowing you to force cleaner into the sealed volume control to clean it. I remember trying to order it, sent a money order only to get it back, where he stated he needed to fabricate some more and was out at the time.

Anyone know who this fellow may be and how to get in touch with him?

One other quick one... Anyone seen or used the chassis tool that you place on your bench top allowing you to more easily work on some of those hard to get to chassis?

Thanks for your replies!
David
#2

Was it Bill Turner? He has such a device listed on his website:

http://www.dialcover.com/components.html

I know Bill has had health problems in the past few years.

Sean
WØKPX
#3

Sean,

I just read your post, got excited and used the email link on Bill's website. My email immediately came back stating that the email box for Bill was full and my email couldn't be delivered. I suspect that he's quite ill as you state and unable to carry his hobby on as he'd like. Hope he's better soon.

Anyone know of anyone else that has a product(s) like his?

Thanks so much!
David
#4

dnitram Wrote:............. My email immediately came back stating that the email box for Bill was full and my email couldn't be delivered........
That's because Bill used some kind of odd e-mail (T.V. based?) and when that service went defunct he never adapted. You either have to call or just send in your order to Bill.

I sent in an order a year or so ago and it seems I read where others also got their orders from Bill recently.

Note the following message taken from his site (homepage):
Quote:Feel free to contact me via telephone for additional information. Email is not available at this time. Orders may be placed in writing with payment enclosed via mail to:
BILL TURNER
1117 PIKE ST.
ST. CHARLES, MO 63301

Tel: (636) 949-2210

CASH, CHECK or MONEY ORDER ACCEPTED
Sorry, no PayPal or credit cards

http://www.dialcover.com/home.html

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#5

Just checked for postings by Bill over on ARF, and it's been a year since he has posted there.

Carl
Northern Panhandle, WV




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
I have a question about this radio, is there anyone that has access to this radio that has an intact unmolested speaker ...captainclock1988 — 04:28 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Well what makes me confuse all of those companies is that all three of those companies (Setchell-Carlson, Stromberg-Carl...captainclock1988 — 04:21 PM
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached.  I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM

[-]
Who's Online
There are currently 4809 online users. [Complete List]
» 1 Member(s) | 4808 Guest(s)
Avatar

>