Posts: 20
Threads: 1
Joined: Dec 2011
City: Spokane, WA
Greetings!
I am starting my first restoration project with a philco 39-7. I am going to replace the electrolytic capacitors, the paper/wax capacitors, and the power cord (It's toast). I will also be checking/replacing the resistors, and any wiring that looks bad.
My first question is how to replace the electrolytic capacitors. I would like to remove the can, but was unable to do so. Plan B is to replace the cap, but put the cap under chassis. The electrolytic has one terminal that extends under the chassis. How do I replace that with one that has the two leads?
Thanks in advance for your replies!
Posts: 91
Threads: 9
Joined: Feb 2010
City: Macon, GA
- lead should be attached to the chassis and the + lead should connect in place of the can terminal under the chassis. DO NOT connect the new capacitor to the terminal of the old capacitor.
Dave
Posts: 20
Threads: 1
Joined: Dec 2011
City: Spokane, WA
Thanks, Dave! That helps a lot.
I did not remove the old cap, but I will NOT connect the new one to the old terminal.
As far as connecting the neg to the chassis, does it matter where? Could I attach it to the nut on the old cap?
Nicole
Posts: 193
Threads: 50
Joined: Oct 2011
City: York PA
I have frequently used this idea gleaned from another forum: solder a terminal strip mounting lug (w/o it having a solder lug on it) to the electrolytic terminal. Then all of the wires that went to the electrolytic will usually reach the new electrolytic mounted to that terminal strip. Getting creative with new filter caps (when not restuffing the cans) is always fun!
Posts: 20
Threads: 1
Joined: Dec 2011
City: Spokane, WA
Thanks, DKinYORKpa.
I think I will try your method.
I wanted to restuff the cap, but I can't seem to remove the old one without risking damage.
Posts: 7,253
Threads: 267
Joined: Dec 2009
City: Roslyn Pa
Hi Nicole and welcome to the Phourm!!!
- lead should be attached to the chassis and the + lead should connect in place of the can terminal under the chassis. DO NOT connect the new capacitor to the terminal of the old capacitor.
Dave
Not necessarily so. Depends on which filter cap. If you look at the diagram http://www.nostalgiaair.org/PagesByModel...013301.pdf you'll see that the negative side of #25 does, but #26 DOESN'T. It goes back to the center tap on the HV winding of the power transformer. If you connect #26 to the chassis it will hum alot. There won't be any filtering for the grid bias on the 41 tube.
Terry
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 20
Threads: 1
Joined: Dec 2011
City: Spokane, WA
Thanks, Terry!
Yes, you are correct. One of the electrolytics is ground to the chassis, and the other does not. Thank you for reinforcing that for me, AND telling me what would happen if #26 was grounded.
Hoping to get started this weekend. Definitely will be posting more questions, I am sure.
Nicole
Posts: 335
Threads: 50
Joined: Apr 2011
City: Apple Creek
State, Province, Country: Ohio
Pictures too. They help us see what your seeing..
Posts: 20
Threads: 1
Joined: Dec 2011
City: Spokane, WA
Yes, Pictures! I know I need them.
Here is what I am looking at now.
[Image: http://i326.photobucket.com/albums/k432/...011029.jpg]
What I have determined so far is that the transformer has been replaced, and so has the rectifier tube. The 84 has been replaced with an 80 and resulting rewiring ... no evidence of anything burning up so my thought was to replace the paper and electrolytic caps, check/replace resistors, and resleeve wiring that is crumbling, and see what happens.
I have a question regarding grounding the neg on #25. there is a two lug terminal strip. on one lug, the .006 mf cap and the line is grounded, and nothing on the other. Can I attach #25 to the lug that has nothing?
[Image: http://i326.photobucket.com/albums/k432/...1029-2.jpg]
Posts: 7,253
Threads: 267
Joined: Dec 2009
City: Roslyn Pa
Yes.
Terry
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 20
Threads: 1
Joined: Dec 2011
City: Spokane, WA
Thanks, Terry.
I have replaced that cap, and am getting ready to replace the other electrolytic. I have some terribly crumbling wire that needs to be replaced/resleeved. I have resleeved a couple of them, and was wondering about replacing the whole wire. The wires I have resleeved are sold, and very thin. What is the appropriate wire to use as a replacement?
Posts: 7,253
Threads: 267
Joined: Dec 2009
City: Roslyn Pa
The wire isn't very critical something like 22 gauge and the insulation should be good for 200v or better. What I do sometimes is use the wire from an old computer power supply but I'm CHEAP. A friend repairs computers and he saves the power supplies for me. Along with the wire there are lots of little goodies on the circuit board. Diodes,bridge rectifier, and caps to name a few. It's not a bad thing if you can replace the bad wire with one that's the same color. Won't make it play any better but may make it easier to fix.
Terry
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 20
Threads: 1
Joined: Dec 2011
City: Spokane, WA
Does it matter if a solid wire is replaced with braided wire? I haven't done so, but was curious. Just in case I mess a wire up resleeving it.
Getting closer for a test. Have to replace the power cord next, then should be ready to test. I am sure I will be asking questions about that when I get there.
Thanks for the replies!
Posts: 7,253
Threads: 267
Joined: Dec 2009
City: Roslyn Pa
I think what mean to say is stranded or solid wire. Braided usually refers to the outside of the wire like shielded wire. Not picking on you but just want to use the proper terms. No the radio doesn't care.
Terry
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 20
Threads: 1
Joined: Dec 2011
City: Spokane, WA
thanks, Terry.
I did mean stranded. I had just been talking with someone about a fuel line for my bug ...
Users browsing this thread: 2 Guest(s)
|
Recent Posts
|
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
|
Hello everyone today I took a trip up to Michigan and picked up a 1930s Stromberg-Carlson Tombstone Radio that I need he...captainclock1988 — 06:05 PM |
Restoring Philco 38-14
|
Well, I climbed down off of that fence and decided to proceed with restoration.
I did experiment with the speaker.
I n...morzh — 03:49 PM |
Philco 71LZ chair side
|
lol not pondering it’s been mine for at least an hour now ?. At a local car show with my Jeep will load it up and take ...slford310 — 01:33 PM |
Philco 71LZ chair side
|
If he only wants $40.00 what are you doing still pondering over it? Go get it! Take care and BE HEALTHY! GaryGarySP — 01:29 PM |
Philco 370LZ
|
Just took a closer look at it. It is a 370LZ not the 71LZ.slford310 — 12:58 PM |
Clear Schematic for 41-255
|
Thank you, Dale. Please take your time. I tried cleaning up a scan in PhotoShop and it helped a little, but after 1.5 hr...RossH — 12:38 PM |
Philco 71LZ chair side
|
He only wants 40 so I think I’ll have to buy itslford310 — 12:13 PM |
Clear Schematic for 41-255
|
Ross -
I have an original 1941 Yearbook, but it will be at least a few days before I can get it out of storage and ma...DaleHCook — 11:57 AM |
Philco 71LZ chair side
|
Are you sure that it is a model 71LZ and not the previous years' 370 Lazyboy? Production for both models appears to be 1...Arran — 11:32 AM |
Philco 71LZ chair side
|
What do you guys think is the max I should pay for this?? Always wanted a chair side radio.
slford310 — 10:52 AM |
Who's Online
|
There are currently 2474 online users. [Complete List] » 4 Member(s) | 2470 Guest(s)
|
|
|
|