Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 38-60
#1

Anyone have the schematics for a Philco 38-60? All I could find was a pdf with a parts list and nothing more ...Thanks Doug
#2

I dont have this model but it doesnt look like much was changed from the 37-60 same tube lineup so more than likely same chassis? Try that one to see if it will help.
#3

I used the 37-60 schematics for mine.
#4

ok thanks guys
#5

Im working on a BAKELITE BLOCK CONDENSER part number 8329 SU not sure what the value is can't seem to find it.Help! Thanks Doug
#6

Not sure if it's a different part, or maybe a missprint or smudge on your parts list, but Chuck has one listed on his site labeled 8328-su. Surf on over to the Philco repair bench and take a peek in the parts value section.
#7

ok found it musta been a typo on the block should be a .03 mf,what can I use if I don't have a .03?
#8

Since the older components weren't designed to the same tollarance that they are today, you've got a little fudge factor that can work to your advantage. Try to stay as close to the original value as possible, but a 10% variance won't hurt a bit & you could probably get away with as much as 20%. It's usually better to err on the high side rather than low. Remember that you can combine multiple capacitors in series or parallel to get different values if you need to.
#9

If you combine a .02 and a .01 in parallel you will have what you need.
#10

Thanks guys found a .03 to use she sounds greaat now! Ty




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
I can't remember, but there was a particular product for loosening glue on the more modern "spiders", used pos...MrFixr55 — 09:43 PM
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM

[-]
Who's Online
There are currently no members online.

>