Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Pilot Cathedral?
#1

I picked up a cathedral radio yesterday and it's a 4 tube set (tubes: 47, 48, 57 and 80). The chassis is flanged and bolts in like other Pilot sets I've see and there is a round Pilot sticker/logo on it, but the ID label isn't on the chassis back. I did the tube layout search and didn't come up with a 4 tube Pilot, just a LOT of other sets. I can't imagine someone would have put a Pilot speaker in a non-Pilot set, but you never know! Anyone have any thoughts, ideas OR can ID this set?? I'll try to attach some pictures. No, I didn't pay $100 :-)

Thanks!
David


Attached Files Image(s)
       
#2

Well it does have 1934-35 RCA/G.E style knobs so those don't belong. I can't comment on the speaker but if it looks like someone spliced the cable going to it that's a good sign that it is a replacement. The tubes installed do not make sense, the 80 is a rectifier which is normal, but the 47 is a 2.5 volt power output pentode, the 57 may make some sense as it's also a 2.5 volt tube used as a detector/amplifier, but the 48 is a 30 volt power output tetrode popularly used in 32 volt DC sets so that tube couldn't possibly work in this set.
Regards
Arran
#3

My bad. The tubes are: 58 57 80 47 (not a 48).
#4

Follow the link below to see if the listing has a hit.

http://www.grillecloth.com/sylvania/tube...ubmit&db=5
#5

rghines1 - I spent 2 or three hours last night going over that list and then trying to search for matching pictures on http://www.radioatticarchives.com/
but I had no luck at all. It's really bugging me!
#6

Hello: neat set! Try the below link and plug in the results from your search on the grillecloth.com finder.

http://www.radiomuseum.org/

There were many off-brands made back then using chassis manufactured by other companies.
#7

Hi David,
Been there done that. Might want to find a circuit that is close and use that as a rough draft. I've got an odd set I got a while back that I never could find much on with the same layout as yours. This one the power transformer was shorted so it got replaced with a new one. The RF coils where starting to unwind those got rewound ect,ect,ect. Anyway it's up and running.

http://www.flickr.com/photos/53710524@N0...hotostream
Terry
#8

Thanks! When I get some more time, I'll begin to research some more.
#9

Well I never determined what make it is, but it's got a dandy Pilot speaker! LOL!!
#10

I've had the same radio for 30 plus years. It says Pilot #51 on the back of mine. I've been missing one of the knobs since I got it but it plays great and has 98% of its original parts. I've never found out much about the radio either.
#11

Its a Pilot, sold under the Twin Coupler brand




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Samlex heavy-Duty bench supply filter question
Hello Everyone, I have one of my Heavy-duty bench powersuplies made by Samlex it's 13.8 volt dc 20-25 amp supply. What I...radiorich — 11:24 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
It's a Glaser Sears changer which Philco's engineers thought was an upgrade over a VM, but in retrospect I'd prefer the ...jeibner — 10:39 PM
AC/DC Transformer-less Sets
Joseph, Thank you for the confirmation. I knew that there must be more to the Transformer-less AC/DC radios than the ...PeterN — 10:30 PM
AC/DC Transformer-less Sets
Good evening, folks. Power station engineer here! The east coast had pockets of DC-only power well into the twentieth...jrblasde — 10:11 PM
AC/DC Transformer-less Sets
Model 40 does not have a rectifier, so it would be a DC only model. This however does not say anything about using...morzh — 08:01 PM
AC/DC Transformer-less Sets
I was wondering if anyone knows if these AC/DC transformer-less sets were actually used on 110v DC anywhere, and when. ...PeterN — 06:35 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
Given the 1960s vintage, it is likely that the cartridge is ceramic, likely more stable. The changer looks like a Voice...MrFixr55 — 05:03 PM
Jackson 665 j2 schematic request
FIXED!daveone23 — 03:55 PM
Bakelite crack repair - what is best epoxy?
Thanks everyone. I appreciate you sharing your experience and looks like I'll work with the 24 hr two part clear epoxy....de371 — 10:25 PM
Jackson 665 j2 schematic request
Without a schematic its going to be hard tracing the wire wound spool resistors.daveone23 — 05:21 PM

[-]
Who's Online
There are currently no members online.

>