Restuffing a thin long cap.
Posts: 15,705
Threads: 551
Joined: Oct 2011
City: Jackson, NJ
I have a Zenith electrolytic that is totally dried up (says 16uF 400V, measures at 1nF and is suspiciously lightweight), and that is very slim and long (under 1" diam. and 5.5" long).
I want to restuff it but not sure where best to cut it. I want it to look undamaged when it's done, but if I cut the top, I simply won't reach to the bottom. Too long and narrow. If I cut the bottom, it will look like you know what.
Anyone has experience dealing with those?
I had no problem with those that were twice as wide, but this one's a challenge.
PS. How do I connect the Negative wire to the aluminum body? (soldering won't work on aluminum.)
(This post was last modified: 05-16-2012, 02:19 PM by morzh.)
Posts: 2,128
Threads: 18
Joined: Oct 2008
City: Merrick, Long Island, NY
Don't seem to be problem replacing a modern 22 mf/450 VDC electrolytic in it's place. Just observe polarity. Forget about stuffing old one unless you are working in a museaum. Negative almost certainly would be "body" but trust the schematic and original connections.
Posts: 15,705
Threads: 551
Joined: Oct 2011
City: Jackson, NJ
Codefox,
Well, I know that, about polarity and such.
I really want this cap in this radio, and this is the sole purpose of this post.
Here is the cap.
Posts: 3,138
Threads: 56
Joined: Apr 2011
City: Lexington, KY
I would first try going in from the top. Using some small long needle-nose pliers and hemostats you should be able to gut the thing and slip in the new cap and fish the leads out the bottom.
If you can't do it from the top I think if you make a thin/clean cut close to the bottom it will not look that bad when reassembled. You can find or fashion a small tube to slip both the top and bottom over and glue/epoxy them together.
I would insulate both leads and run them out the bottom and then connect the applicable one to ground under the chassis at a convenient location.
Worst case scenario would be to leave the old capacitor on the chassis and mount a new one underneath. That's the way an old repair shop would have handled it, and you could even stuff the new cap into an old axial electrolytic for a period correct looking repair. Just a couple of ideas for you to think over.
John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
Posts: 15,705
Threads: 551
Joined: Oct 2011
City: Jackson, NJ
John,
Thanks, yes, the axial electrolytic is not a bad idea.....provided I can get me one of the old.
As for the two insulated wires out, you probably mean something like this?
Those had insulated body and two wires and this is how i re-stuffed them; I can make this one look like it too.
Actually this is an even better idea, as the length precludes me from soldering to the center pin, but if I don't need it and am out to simply gut the cap and remove the center pin, it requires no finesse and can be done even with this length to width ratio.
Thanks, I think I know what I'll do.
It pays to discuss things.
(This post was last modified: 05-16-2012, 10:00 PM by morzh.)
Posts: 15,705
Threads: 551
Joined: Oct 2011
City: Jackson, NJ
I will post photos either today or tomorrow: I cut off the top cap with my Dremel and the cutting disk, right at the groove, so it will look fine.
Insides were as dry as H**l on a hot day in June.
Taking them out did not pose any problems, and there was no tar or anything. It was dry dry.
The central rod is quite high and should it be solderable I'd have no problem soldering to it, but I think it is not, and it is attached to the solder contact with a rivet of some sort.
So as I planned, I will remove it and go with two wires.
I will wait 'till I finish, but so far it is not nearly as bad as I thought it would be.
Posts: 2,128
Threads: 18
Joined: Oct 2008
City: Merrick, Long Island, NY
Posts: 15,705
Threads: 551
Joined: Oct 2011
City: Jackson, NJ
Oh Me lave los manos, sin duda. Load of dust and who knows what else.
But then any opened electrolytic commands the same handwashing: wet or dry, it is all possibly very toxic if ingested.
PS>
Here, I made some pics.
(This post was last modified: 05-18-2012, 07:25 PM by morzh.)
Users browsing this thread: 1 Guest(s)
|
Recent Posts
|
Philco 91 Speaker Replacement
|
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM |
Restoring Philco 37-604C
|
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one.
Which does not m...morzh — 01:44 PM |
Philco 38-2 Automatic Tuning
|
When you push the lever, you are supposed to rotate the disk to the desired station.
Then the magnetic tuning will acqu...morzh — 01:42 PM |
Philco 38-2 Automatic Tuning
|
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM |
Philco 91 Speaker Replacement
|
How would I go about removing the spider from the cone?dconant — 12:04 PM |
Philco 38-2 Automatic Tuning
|
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM |
Does anyone make photofinish replacements?
|
Here’s the link to the DIY photofinish section of our site:
klondike98 — 09:46 AM |
Delco car radio Peko vibrator converstion issues
|
Hi Richard,
Thx for posting the schematic. As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM |
Delco car radio Peko vibrator converstion issues
|
hello mr Fixr,
The Electro Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM |
Delco car radio Peko vibrator converstion issues
|
How about putting a choke in the power supply?
The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM |
Who's Online
|
There are currently no members online. |
|
|