Philco 66 - Sweet Music at Last!!
Posts: 80
Threads: 10
Joined: Apr 2012
City: Waterford, NJ
Have tracked down a 2nd Philco 66- {different cabinet} that is almost all original and it works. I have been comparing the two with voltage readings at all tubes. The original is wired exactly like the new one but voltages are higher in the original.
On the original- soldered in the wire from white of 42 to 28 and 29 terminal. Hum on center tap of vol. control that is controlled by vol. control. Set up signal gen. on 460 and went through antenna- nothing through speaker.
Touched grid cap of 6A7-nothing
Touched grid cap of 75- nice clear tone.
Suggestions?
Thanks,
Joe
Posts: 15,511
Threads: 544
Joined: Oct 2011
City: Jackson, NJ
First of, Jph, injecting if freq. in antenna is not supposed to produce any tone. Antenna is connected to the RF amp an the tuned circuit will only let through the frequency it is tuned to. In prder for the IF to prduce the tone you need to feed it to the input of the IF filter, or output of it, that is the detector input.
This is why radios are tuned to stations' freqs.
Should've said that earlier when it was first suggested to you.
Posts: 7,270
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
The model 66 doesn't have a rf amp but injecting the IF signal into the grid cap of the 6A7 will work fine. When you connect to the ant post the signal has to go though a tuned circuit that isn't resonant at the IF frequency hence it will attenuate the IF signal.
Terry
Posts: 80
Threads: 10
Joined: Apr 2012
City: Waterford, NJ
I did remove the grid cap of 6A7 and injected 460 from there. Got good tone. Did adjust the four trimmers for max. Good start.
Just to try I hooked up antenna through ant. clip- got no channels but did get interference from shop lights.
Have to adjust wave trap and tuning condensor-- any pointers? I tried following the alignment procedure but am confused on this.
You guys have certainly taken me much deeper into this than I was capable of.
Will continue work this weekend but feel like we're getting close.
Thanks,
Joe
(This post was last modified: 05-31-2012, 08:21 PM by jph14.)
Posts: 7,270
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
So what happens if you inject a 1000kc signal into the ant post and tune the set around 1000kc?
Terry
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
My bad Joe, sorry, yes if you inject from the antenna, you need to set your generator to a radio frequency then check at that frequency. Thanks gang for correcting me. I was thinking about injecting in the IF stage. Keep going Joe, it's going to work. Follow Terry's advise and see if you pick up the tone around1000 on your dial. When you find it, then you can adjust your osc. and ant. trimmers per the directions for alignment to bring it spot on. If you can find the signal, your almost home, your oscillator is working!
Jerry
A friend in need is a pest! Bill Slee ca 1970.
(This post was last modified: 05-31-2012, 09:35 PM by jerryhawthorne.)
Posts: 7,270
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
If you are going to use this to align the set it should be a bit higher in frequency like 1400kc. I picked 1000kc cause it's closer to the center of the dial, might be easier to find.
Terry
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
Correct Terry, which is why I suggested to align per factory specifications. I probably was not clear.
 Jerry
A friend in need is a pest! Bill Slee ca 1970.
Posts: 80
Threads: 10
Joined: Apr 2012
City: Waterford, NJ
1400 nothing - cannot find it on the dial. Signal through the antenna clip?
Joe
(This post was last modified: 06-01-2012, 02:35 PM by jph14.)
Posts: 7,270
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Ok Take a transistor radio and place it next to the 6A7 tube. Tune it to 1500kc. Adj the dial on the Philco with it set to the BC band. If all is well at some point you should hear a hum in the transistor set. That is the signal from the local oscillator.
Terry
Bump my needle I feel like a broken record.
Posts: 80
Threads: 10
Joined: Apr 2012
City: Waterford, NJ
Tried transistor radio near 6A7- did not get any hum from Philco.
Joe
Posts: 15,511
Threads: 544
Joined: Oct 2011
City: Jackson, NJ
Did you try to adjust your Philco, as your 1500kHz may not necessarily be accurate?
Posts: 80
Threads: 10
Joined: Apr 2012
City: Waterford, NJ
Yes. Got nothing across dial.
Posts: 7,270
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Ok Double check 8, 200 ohms, 10, 50K ohms and 15, 32K ohms. Replace 14, 800mmfd.
Measure resistance from the coil side of #10 to pin 5 of the 6A7.
Measure resistance from the coil side of #10 to coil side of #14
Both should read only a few ohms. If not You've got a bad coil.
Terry
Posts: 80
Threads: 10
Joined: Apr 2012
City: Waterford, NJ
Resistors check OK. #14- how close do I need to be - I have a 700 in stock.
Resistance from coil side of #10 to pin 5=@ 4 ohms
Resistance from coil side of #10 to coil side #14= open.
Thanks,
Joe
Users browsing this thread: 4 Guest(s)
|
|
Recent Posts
|
|
Samlex heavy-Duty bench supply filter question
|
| I suggest sticking with the original values. Depending upon the design if you increase the cap values too much the incre...DaleHCook — 08:55 AM |
|
AC/DC Transformer-less Sets
|
| You’re welcome! I was born in 1995, so this is all second-hand information to me from the industry. I did some research ...jrblasde — 08:38 AM |
|
Samlex heavy-Duty bench supply filter question
|
| Hello Everyone,
I have one of my Heavy-duty bench powersuplies made by Samlex it's 13.8 volt dc 20-25 amp supply.
What I...radiorich — 11:24 PM |
|
Looking for place to donate unique Philco Philco J-1930 Prototype
|
| It's a Glaser Sears changer which Philco's engineers thought was an upgrade over a VM, but in retrospect I'd prefer the ...jeibner — 10:39 PM |
|
AC/DC Transformer-less Sets
|
| Joseph,
Thank you for the confirmation. I knew that there must be more to the Transformer-less AC/DC radios than the ...PeterN — 10:30 PM |
|
AC/DC Transformer-less Sets
|
| Good evening, folks. Power station engineer here!
The east coast had pockets of DC-only power well into the twentieth...jrblasde — 10:11 PM |
|
AC/DC Transformer-less Sets
|
|
Model 40 does not have a rectifier, so it would be a DC only model.
This however does not say anything about using...morzh — 08:01 PM |
|
AC/DC Transformer-less Sets
|
| I was wondering if anyone knows if these AC/DC transformer-less sets were actually used on 110v DC anywhere, and when.
...PeterN — 06:35 PM |
|
Looking for place to donate unique Philco Philco J-1930 Prototype
|
| Given the 1960s vintage, it is likely that the cartridge is ceramic, likely more stable. The changer looks like a Voice...MrFixr55 — 05:03 PM |
|
Jackson 665 j2 schematic request
|
| FIXED!daveone23 — 03:55 PM |
|
Who's Online
|
There are currently 6349 online users. [Complete List]
» 2 Member(s) | 6347 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
