Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

40-145 speaker hole
#1

Just got this one in the mail and was wondering how do I fix about a quarter size piece of speaker cone that is missing? Other than that the radio looks good. I just started the recap on it.

What is the best material to try and patch it and what is the best kind of glue or cement? How difficult is this to do?

thanks
Chris
#2

It's an easy repair. I harvest a patch from an unused tea bag. Make sure it's large enough to cover the hole plus at least 1/2" all the way around. GENTLY spread some flexible fabric glue around the hole, apply the patch & gently brush more glue over the patch. If you can get to the back side of the cone, repeat the process on the back. Be very careful, the old paper on speakers can be extremely delicate & can tear easily, especially when wet with glue.
#3

Dave,
Thanks for the tip. never thought of using a tea bag! Will give it a try.

Chris
#4

I always used something like a good quality of bond paper to patch holes in speakers, a tea bag may be good to re-enforce a tear after gluing but it's pretty thin to cover a hole. Also remember, do not use silicone inspite of what you may have heard, silicone is for the bathtub not speaker repair.
Regards
Arran
#5

Over the years I've seen a lot different things used. Mostly bad stuff! Duck tape, news paper and white glue, masking tape, and Scotch #33 tape (black electrical tape) One guy insisted on using RTV silicone. If I sat down a thought for a few hours I couldn't think of much worst to use. I was more of a rubber cement kind of a guy but with these new glues and such it opens the doors for much better repairs
Terry
#6

Best is a little left over from the last time you bought a surround kit and didn't use it all up. I think it's similar to fabric glue, but I'm not a chemist. Reckon Somewhere between Elmer's and Rubber Cement.
#7

Best is a little left over from the last time you bought a surround kit and didn't use it all up. I think it's similar to fabric glue, but I'm not a chemist. Reckon Somewhere between Elmer's and Rubber Cement.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
My Philco 37-116 Restore
Measuring from center tap like the tube voltages show. Cap 127 is isolated from ground. Cap 127 shown in upper left of p...dconant — 08:05 AM
My Philco 37-116 Restore
Are you measuring relative to the centertap or the GND?morzh — 11:57 PM
Philco 610B oscillator wiring
Still not clear on the wiring interface between the 6A7 and oscillator. After refering to the available schematics and s...Tubester — 07:18 PM
Refinishing Ideas
My 37-116 code 121 is the best sounding radio i have...a daily driver. Since we are talking about "changes". ...poulsbobill — 07:18 PM
My Philco 37-116 Restore
Hello, I finally got brave enough to take the cans off the Expander Unit. Got the grid cap wires replaced and back toget...dconant — 06:50 PM
Zenith H725
I got into the first AM IF can today, and found its mica was cracked. Amazing that it was still working. This one makes ...EdHolland — 06:10 PM
Philco model #20
AHH HA , I got it and can’t thank you fellows enough , when I changed the capacitors I took the advice and did not unsol...onlyrick — 02:24 PM
Zenith H725
Hello Ed, yes, I like letting projects run for few days to make sure they don't start acting up . Sincerely Richardradiorich — 01:03 PM
Philco 46-480 Electronic Restoration
I am almost finished with this restoration. All which remains is the power transformer. I cleaned it up some time ago, b...jrblasde — 12:41 PM
Philco model #20
I seem to recall in some TRF sets there being a Local/Distance toggle switch that removes the B+ from the first 24 rf tu...RodB — 09:46 AM

[-]
Who's Online
There are currently 655 online users. [Complete List]
» 1 Member(s) | 654 Guest(s)
Avatar

>