Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

40-145 speaker hole
#1

Just got this one in the mail and was wondering how do I fix about a quarter size piece of speaker cone that is missing? Other than that the radio looks good. I just started the recap on it.

What is the best material to try and patch it and what is the best kind of glue or cement? How difficult is this to do?

thanks
Chris
#2

It's an easy repair. I harvest a patch from an unused tea bag. Make sure it's large enough to cover the hole plus at least 1/2" all the way around. GENTLY spread some flexible fabric glue around the hole, apply the patch & gently brush more glue over the patch. If you can get to the back side of the cone, repeat the process on the back. Be very careful, the old paper on speakers can be extremely delicate & can tear easily, especially when wet with glue.
#3

Dave,
Thanks for the tip. never thought of using a tea bag! Will give it a try.

Chris
#4

I always used something like a good quality of bond paper to patch holes in speakers, a tea bag may be good to re-enforce a tear after gluing but it's pretty thin to cover a hole. Also remember, do not use silicone inspite of what you may have heard, silicone is for the bathtub not speaker repair.
Regards
Arran
#5

Over the years I've seen a lot different things used. Mostly bad stuff! Duck tape, news paper and white glue, masking tape, and Scotch #33 tape (black electrical tape) One guy insisted on using RTV silicone. If I sat down a thought for a few hours I couldn't think of much worst to use. I was more of a rubber cement kind of a guy but with these new glues and such it opens the doors for much better repairs
Terry
#6

Best is a little left over from the last time you bought a surround kit and didn't use it all up. I think it's similar to fabric glue, but I'm not a chemist. Reckon Somewhere between Elmer's and Rubber Cement.
#7

Best is a little left over from the last time you bought a surround kit and didn't use it all up. I think it's similar to fabric glue, but I'm not a chemist. Reckon Somewhere between Elmer's and Rubber Cement.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
AC/DC Transformer-less Sets
Some of the original Edison DC generators were in use until the 1940s. The NYC subway and electrified Long Island Rail ...MrFixr55 — 09:39 AM
Samlex heavy-Duty bench supply filter question
I suggest sticking with the original values. Depending upon the design if you increase the cap values too much the incre...DaleHCook — 08:55 AM
AC/DC Transformer-less Sets
You’re welcome! I was born in 1995, so this is all second-hand information to me from the industry. I did some research ...jrblasde — 08:38 AM
Samlex heavy-Duty bench supply filter question
Hello Everyone, I have one of my Heavy-duty bench powersuplies made by Samlex it's 13.8 volt dc 20-25 amp supply. What I...radiorich — 11:24 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
It's a Glaser Sears changer which Philco's engineers thought was an upgrade over a VM, but in retrospect I'd prefer the ...jeibner — 10:39 PM
AC/DC Transformer-less Sets
Joseph, Thank you for the confirmation. I knew that there must be more to the Transformer-less AC/DC radios than the ...PeterN — 10:30 PM
AC/DC Transformer-less Sets
Good evening, folks. Power station engineer here! The east coast had pockets of DC-only power well into the twentieth...jrblasde — 10:11 PM
AC/DC Transformer-less Sets
Model 40 does not have a rectifier, so it would be a DC only model. This however does not say anything about using...morzh — 08:01 PM
AC/DC Transformer-less Sets
I was wondering if anyone knows if these AC/DC transformer-less sets were actually used on 110v DC anywhere, and when. ...PeterN — 06:35 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
Given the 1960s vintage, it is likely that the cartridge is ceramic, likely more stable. The changer looks like a Voice...MrFixr55 — 05:03 PM

[-]
Who's Online
There are currently 4436 online users. [Complete List]
» 2 Member(s) | 4434 Guest(s)
AvatarAvatar

>