Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

32 volt Philco
#1

I am looking for a 32 volt Philco or other brand in working condition.
How many were made and what models were they?.
I am more familiar with the Delco R32xx series that were popular as well.
I have a 32 volt Delco system, and like to display working 32 volt lights and other appliances.
Thank you

Mike
#2

The only one I am aware of is the model 32, which is based on the Philco 89 circuit. I understand that they are quite rare. I found one on eBay, but it is not for sale. Its restoration is documented on my web site:
http://mcclellans.com/Philco32B.htm

Dave
#3

Correction to my last post - I was referring to PHILCO 32 volt sets that I am aware of. I have the following 32 volt sets in my collection, and many more exist:

Airline 62-138 (Wells-Gardner Series 6B)
Silvertone 1925
Universal Battery Company 6132
Universal Battery Company 7232
Erla (Sentinel) 67L(134BL)
Karola (Brame Mfg Co Mnps)
Coronado (by Wells-Gardner & Co.) Series 7T5
Setchell Carlson 437
Delco 3201

Others:
Midland B6B
Knight 5646K(?)
Coronado (Gamble Scogmo) 36L
Crosley 159
Coronado (by Gamble-Scogmo Inc. Ch 36-L) 36L8600
#4

Dave is correct on the Philco model 32. It was made in different cabinets for several years until about 1935. These used vibrator supplies for high voltage. Philco made a model for the 1936 model line, their last 32 volt set model 642 which like some of the other sets made used low voltage, 32 volts for B+ with type 48 tubes in push pull. I have a Lafayette 32 volt set like the Philco 642 with type 48's. The power output is only about a third of a watt but the set performs amazingly well with only 32 volts on the plates of the tubes.

Fred R
#5

Do either of you have a working one for sale?
Again, I have the 32 volt system, and actually use Edison batteries to store the electricity.....




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM

[-]
Who's Online
There are currently no members online.

>