Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Dial Philco 66S and dial philco 66B
#1

hello i have two tombstone philco, but they have diferent dial, the Philco 66s have the scale dial number 27-5081 and the philco 66b have the dial 27-5057, some have this radio ????

are originall this dial of ths two radio ??????????????

thank you, Mauricio
#2

Hi Mauricio,

The information I have access to says the dial for the Philco 66B is indeed part number 27-5057. This is a tombstone radio with the small window for the dial - is that correct? (Philco also made a cathedral radio with this model number). Here's a picture of the 66B from Ron's website.

http://www.philcoradio.com/gallery/1935a.htm#ae

The 66S has a much more ornate grill than the 66B, but I don't have any other specific info on it. I'm sure there is someone here that has access to better info than I do. Here's a picture of the 66S from Ron's website.

http://www.philcoradio.com/gallery/1935c.htm#n

It is possible that your 66S has the correct dial with part number 27-5081, but I'm not able to verify it.

Those are both very nice radios!

Bill

Sent from my Pentium II on the AT&T Dial Network
#3

thank you, Bill, yes the dial of radio 66b is 27-5057, of this i m segure, but i can not find infromation of dial 66-s.

i have this radio, the radio 66-s is small and more nice for me.

thank you, mauricio




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM

[-]
Who's Online
There are currently 3219 online users. [Complete List]
» 4 Member(s) | 3215 Guest(s)
AvatarAvatarAvatarAvatar

>