Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

A new piece for my basket case
#1

After keeping my eyes open everywhere and posting a few ads online on here and the "Barking Dog" forum I finally found a replacement chassis for my Canadian G.E E-81 E-81 from 1937-38. Similar to the one on Radio Attic here:

http://radioattic.com/item.htm?radio=0960690

Ignore the demented price, it isn't worth 1/4 of what he's asking even restored.

The one currently in my E-81 is a horribly rusted mess, repairable in theory but really too much work and is better used as a parts chassis. Through flipping through some schematics I have found out that the chassis of the E-81 was not only used in a console version, the E-86 but is almost an exact clone of the Canadian RCA Victor models 8T-2 and 8K-1. It is also a doppelganger of the American RCA models 7T, 7K, and 8T, 8K. In any event the E-81 and the RCA 7K are identical electrically and physically with the exception of an added eye tube cable and socket, which I have. Here is the chassis I just bought through the usual auction site:

http://www.ebay.com/itm/160858739314?ssP...1439.l2648

Here is the schematic for the E-81:

http://www.nostalgiaair.org/Resources/970/M0028970.htm

Here is the one for the U.S RCA 7K/7T:

http://www.nostalgiaair.org/Resources/135/M0015135.htm

In spite of what the listing says it is an RCA model 7K not a 6K2, it has seven tubes and is the same circuit as the other sets I mentioned, minus the Magic eye. This chassis is not pristine as you can see but everything is there, and it is still five time better then my E-81 which even had crusty rust on the pilot bulb sockets. So when I eventually get this chassis this American made RCA will spend the rest of it's days as an C.G.E E-81, have a hole drilled in the chassis, and have the Magic Eye socket and cable added from my E-81 along with any other bits it needs. The one thing it will not have is a 25 cycle transformer but I think that the black unit on this chassis may be a replacement anyhow.
Regards
Arran
#2

Arran, A great find, and impressive research! Icon_thumbup Joe

Joe

Matthew 16:26 "For what does it profit a man if he gain the whole world, yet lose his own soul?"
#3

Good job, Arran! Icon_thumbup

Looking at the photos in the eBay ad, I see one paper cap that wasn't replaced. Those RCA mica caps that look like cough drops might be suspect, also.

--
Ron Ramirez
Ferdinand IN
#4

Quote:Good job, Arran! Icon_thumbup

Looking at the photos in the eBay ad, I see one paper cap that wasn't replaced. Those RCA mica caps that look like cough drops might be suspect, also.

Well Ron, it will be quite a while before I get around to working on it, since the previous owner thought it was a 6K2 it's possible he may have been working from the wrong schematic so it could have one or two wiring errors.
So far I haven't had many problems with the mica caps in these sets, and they were using ones of that design right up until the war. The main issue seems to be the cases splitting and falling apart more so then leakage, I think it's one of those alleged problems that the internet rumor mill has blown out of all proportion like 6X5 tubes. If there is a problem with one or few I can deal with that but shotgunning them all may cause more problems then it solves. Like every other set I leave the changing of micas as a last resort when everything lese is exhausted.
It is also going to my friend's place in Montana for the time being since the set is in Butte, Montana, a shorter trip lessons the chance of damage, so it will be picked up in maybe a year's time. I have a full set of knobs for this radio and even have the proper speaker, though it needs to be reconed.
I think that I should mention why I went to so much trouble to find a chassis for this set. I bought this radio with a basement/shed full of radios in 1993, along with a Philco 96, a Philco 60, a Canadian Marconi type 12, two G.E consoles, and an assortment of table sets including this E-81 and a Philco 3118 tombstone. There was a lot of stuff that was basically scrap, rusty chassis, beat up sets with broken dials, smashed Bakelite sets, but I did save every set that was more or less intact. The E-81's chassis was badly rusted and almost junk, but it was all there, and it had one thing that made it stand out, it was the exact make and model of radio that my Great Grandfather once owned.
Up until now I haven't been able to find a replacement chassis and just kept it on the back burner since I had lots of other sets to restore. I did see an E-86 console in a junk/antique store about 10 years ago but the condition was too good to just part out. For some reason I have seen all sorts of years and models of C.G.E sets over the years but never an E-81 for sale, except from that guy on Radio Attic.
Regards
Arran




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
New Philco Repair Bench
I am sure this is the archive, and not the Chuck's site.morzh — 09:50 PM
Made mistake & did not label connection
It's not like we are good friends with that wire and can tell it from other ptetty identical looking wires. Why'n't you...morzh — 09:49 PM
Made mistake & did not label connection
I'm not sure why that wire wasn't covered in the video. I'm pretty sure the 6A8 won't work until that pin is grounded. Y...RodB — 09:47 PM
Made mistake & did not label connection
You'll have to forgive me, I am not sure what you mean.  Can you explain what you are really saying.  If anyone does not...georgetownjohn — 08:05 PM
Made mistake & did not label connection
Those are details better left to the ones who know. Maybe you disconnected the wrong end of the wire.RodB — 06:22 PM
Made mistake & did not label connection
Maybe this is starting to make some sense in my hard head.  Is this why the wire in question was not in the great Ron Ra...georgetownjohn — 04:34 PM
Made mistake & did not label connection
I was correct with the 6A8 pin connection's, 7 and 8 are connected to ground as well as the tube shield (the broken line...RodB — 02:41 PM
Made mistake & did not label connection
What does the dotted line representing that surrounds the tube in the schematic?georgetownjohn — 02:17 PM
Made mistake & did not label connection
Hello John, I have been there either label got lost or was not labeled ! Sincerely Richardradiorich — 02:15 PM
Made mistake & did not label connection
Sorry, it is a Philco 37-640.  Does that help?--Johngeorgetownjohn — 02:14 PM

[-]
Who's Online
There are currently no members online.

>