Posts: 16,266
Threads: 566
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
Well, now that I have bought it and picked it up from very nice folks, I am starting with it.
Here are the first pics:
Here's how it looks. Not bad.
The inside is a bit dusty.
And the caps have rabies.
And the grill cloth is nonexistent though enough is left to see what it was.
Now, with this foaming cap the owner told me he kept powering it up. Even before I bought it. I wrote to him then that no matter what happens, he should not be powering that thing with the cap looking like it is.
Now it is up to me to fix it all up.
I will update you as I go.
Mike.
Posts: 1,407
Threads: 72
Joined: Oct 2007
City: Linn Creek, MO
Great find! The Philco 18 is an outstanding performing radio. 
Steve
M R Radios C M Tubes
Posts: 16,266
Threads: 566
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
Thanks, Steve,
That was the consensus here when I asked.
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
So, The previous owner kept trying to re-FOAM that cap?
(silly rabbit)
Posts: 16,266
Threads: 566
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
I guess, yeah....foam keeping copming out of a cap can be aesthetically pleasing to watch while listening to some well-matched music.
Posts: 7,294
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Hey Mike
Nice set!!! It make me want to work on the 14 I just got. To be truthful I haven't been doing much radio work since early spring except for picking up a few set. Got this car radio I've had for tooo long that needs to get finished for a customer but haven't felt motivated to work on it.
Looks to be all in good shape so hopefully it will be a easy job to get it working again. Is it BCB only?
GL
Terry
Posts: 4,816
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA
I think some early version 18s are broadcast band only, many have the police band as well, which would include the upper end of the broadcast band, the 118s have one shortwave band though.
Regards
Arran
Posts: 1,407
Threads: 72
Joined: Oct 2007
City: Linn Creek, MO
Actually, I think it was the later version that was broadcast band only.
Steve
M R Radios C M Tubes
Posts: 4,816
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA
Did they extend the broadcast band past 1500 KC on the updated version eliminating the need for the extra band?
Regards
Arran
Posts: 1,407
Threads: 72
Joined: Oct 2007
City: Linn Creek, MO
Yes, I think the late version went up to about 1700 kc.
Steve
M R Radios C M Tubes
Posts: 1,407
Threads: 72
Joined: Oct 2007
City: Linn Creek, MO
Arran, I just checked Ron's photo gallery and it shows the late version 18 as having a coverage of 540 to 1720.
Steve
M R Radios C M Tubes
Posts: 16,266
Threads: 566
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
I can check the dial figures later. Right now I am trying to figure out if I should go to work or stay home. 
Took the chassis out, dusted it a bit. Needs cleaning.
Underbelly looks very clean and colourful, unlike my other Philcos, really bright colors. The resistors, mostly. A pity - many of them will likely have to go, but I hope, if the colours are that good, maybe some of them survevied well enough to be kept in.
Even the caps look good! Some of the large axial caps are there, not the backelite Philco type. Will see if they can pass for leakage/value, if not - I will keep the outer shell and stuff it with new ones, same way as the electrolytics. Wires are good too!
The cord is probably not original, though it is the cloth-covered type, and only has outer cloth ripped in one place in the middle, and the wires inside (also cloth-covered) seem to look very good, soo I wonder if I shoud replace the cord or keep it. I think it is not original since the pluig is not typical brown round with Philco logo, but rectangular without logo, though seems old enough to be from 60-s - 70-s.
I wonder if anyone sells Philco power plugs.
OK, back to watching the storm.
Posts: 16,266
Threads: 566
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
Went to check the dial.
The BC band is marked from 55 to 150, so it is 1.5MHz (ok, ok, 1500kc).
The other band is marked from 1.7MHz to 4.0MHz.
So I probably have the earlier version?
Posts: 1,407
Threads: 72
Joined: Oct 2007
City: Linn Creek, MO
Morzh, if some of the resistors need to be replaced and you really want to keep the original look of the underside of the chassis, it is not too hard to make some reproduction "dog bone" resistors. Here are a couple that I made. [Image: http://i985.photobucket.com/albums/ae335...ff/003.jpg]
To make them, simply select a modern resistor of the value you need, solder on some longer leads. Next, take a piece of plastic tubing that is about 5/16 inch in diameter and cut it to the length you want and cut a small notch in each end to bring the wires out the side. Now insert the resistor into the tube and wrap the leads two times around each end of the tube. While holding the wrap tight, solder the wrap. Then fill the inside with JB Quick and smooth the ends. After the JB sets up, paint. It makes some really neat looking dog bone resistors.
Steve
M R Radios C M Tubes
Posts: 4,816
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA
That tubing trick sounds like a cheaper and quicker method then trying to mold a complete "dogbone" out of some sort of molding compound.
Regards
Arran
Users browsing this thread: 3 Guest(s)
|
|
Recent Posts
|
|
An attempt to remove the Field Coil from a G speaker
|
| Mike;
I've only run into a speaker with an open filed coil twice, and they were on newer speakers from the 1940s. One ...Arran — 12:48 AM |
|
An attempt to remove the Field Coil from a G speaker
|
| Arran
Yes, this is my plan for now and what do I got to lose, this is not even the speaker from this radio, but one o...morzh — 10:44 PM |
|
An attempt to remove the Field Coil from a G speaker
|
| Mike;
I would unwrap the field coil, and see if maybe there a break near one of the ends, like where the coil wire att...Arran — 10:23 PM |
|
An attempt to remove the Field Coil from a G speaker
|
| ...and this is what I did. I fed a little LT into the screwholes with a small brush, and a little on the rim next to the...morzh — 09:52 PM |
|
Philco 40-120C Restoration
|
| I combined the two 40-120C threads together as we like to keep the discussion of the same radio together. It helps with...klondike98 — 09:36 PM |
|
Philco 40-120C Weak, Distorted Ouput
|
| Just checked were I buy tubes price is four dollars. So living in Florid we have a local source for tubes. David David — 09:14 PM |
|
Philco 40-120C Weak, Distorted Ouput
|
| The higher voltage may be due to higher mains voltage. My mains run 120-125AC when the set was new mains would be 110-11...David — 09:09 PM |
|
Philco 40-120C Weak, Distorted Ouput
|
| Thank you for your reply. I pulled a speaker from a Philco 41-221 and received the same result. I used a signal tracer t...bluecap — 08:45 PM |
|
Philco 40-120C Weak, Distorted Ouput
|
| Have you tried a different speaker?
How did you trace the distortion?
How do you know it is weak? What is the reference?...morzh — 08:33 PM |
|
Philco 46-480 Electronic Restoration
|
| Amen to that! Every time I think I’ve captured them all, I realize that there’s another error. My goal is to finish with...jrblasde — 07:00 PM |
|
Who's Online
|
There are currently 2298 online users. [Complete List]
» 1 Member(s) | 2297 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
