Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

RCA Victor R-15
#1

Could someone with Riders volume 1 scan a copy of the schematic for the RCA Victor R-15 for me? I believe it is on 1-14 under RCA Victor.

The copy on Nostalgia Air is unreadable and Riders Vol 1 is one that I don't have.

Thanks

-Keith
#2

It's also a Radiola 48. The big, heavy vertical TRF chassis, right?

Those sets must have been in a contest with the Baldwin Locomotive Company for weight. However, they were reportedly very good sets.

I'm sure I have the RCA Radiola 48 service book, but just where to look is the problem.
#3

The early Victors are surprisingly GOOD receivers for TRF sets. I had an RE32 that had amazing reception. It had, if I remember correctly, FOUR RF amplifier circuits before the detector.

HOWEVER, the Victors are TOUGH to work on.
#4

Keith, I have a copy of the R-15 from Vol I that you requested. Let me know how to get it to you.It is a pretty good copy.

Dave D
#5

Ijust did a google search for: "RCA Radiola 48. It has the entire RCA service booklet with a clear full page schematic diagram, as well as the rest of the book.
#6

Thanks Dave and Doug for the info.

I hope it turns out to be a good performer. I have had it for a few years now got it from my parents for a birthday present. It's missing the dial bezel which i have been hunting for since I got it. The cabinet is in good shape except for the veneer on the top is shot and will need to be replaced. The press wood looks very good.

-Keith
#7

Keith: you might want to take a look at the radiolaguy website, he may have what you are looking for....




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

[-]
Who's Online
There are currently 5545 online users. [Complete List]
» 3 Member(s) | 5542 Guest(s)
AvatarAvatarAvatar

>