Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 112 highboy found
#1

If anybody wants one, there is a Philco 112 higboy in an antique shop in Yucco Valley, California. I told the manager/owbner that the $450 price was a factor of ten too high. However, the cabinet can be saved without refinishing, a big plus. Just some touch-up to the legs would be needed. I suspect this may be one of the models with transformers which go bad with green corosion on the wires. Is it?

Web site: http://www.masekconsulting.net
Radio Photos: http://www.photobucket.com - album id FStephenMasek
#2

Less likely in the 112, but the "green disease" does sometimes strike 112 coils, also.

$450...yikes! Icon_eek

I had one of those for awhile...passed it on to another Phorum member...who passed it on to yet another Phorum member. So it slowly made its way from central to southern Indiana, and then to North Carolina by way of the Cincinnati area. Very nice-looking sets, and uncommon as well, but not $450 uncommon.

--
Ron Ramirez
Ferdinand IN
#3

If it was closer and cheaper, I would have been tempted to leap on it. Going to thin my herd down to mostly my Philcos anyways depending on my mood next year.

No matter where you go, there you are.
#4

Those are a nice looking cabinet, designed by Norman Bell Geddes I think, but unlike some industrial designers there hasn't been a pseudo radio collector/antique dealer attempting to start a cult following with the man's work. I actually wouldn't mind getting one of the 112s, they used a pan chassis similar to the one in my Philco 96 but were superheterodynes, I'm not paying $450 for one though, maybe $150 at most if it was in really good shape, unrestored but sort of playing.
Regards
Arran
#5

My 112 is an excellent set. Strongly recommended!!!
#6

Maybe I'll add the Philco 112 to my bucket list. Icon_smile

No matter where you go, there you are.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W  1.5k  ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM
Philco 60 Squealing
I have taken out the 2nd IF and found a problem or not. I believe the coils are litz wire. There is a very small strand ...dconant — 02:13 PM
Philco 6K7
I am restoring a Philco 37-60. The am reception is very good, but the shortwave is very weak. Run 6 Philco removes the g...bobbyd1200 — 01:35 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A5...MrFixr55 — 06:48 AM

[-]
Who's Online
There are currently 5055 online users. [Complete List]
» 4 Member(s) | 5051 Guest(s)
AvatarAvatarAvatarAvatar

>