Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

40-215 opinions wanted
#1

Hey everyone,
There is a listing on Craigslist for what the owner says is a Philco 40-215. not too far from me. I'm not normally into Philcos of this period, but have been thinking I would like to get one with the "Mystery Control". Is this set one that would have it? The seller makes no mention of a control unit, so I don't think it has one. If it is a mystery control model, will any other control unit work with it? I would also like to get anyones opinion of what a fair offer would be? The seller is asking $200 but says price is not firm. It looks to be in fair condition, although it looks like it might be missing some veneer on the front. I might be interested in it and would like to make an offer, but not sure where to start on this one. Any input or opinions on this set would be greatly appreciated! Thanks!
Kevin
http://sheboygan.craigslist.org/atq/3506288127.html
#2

It has chipped veneer on the front but the finish on the top is also shot. It would be nice if there were some photos of the sides of the cabinet as well. I wouldn't know where to begin on an offer, to me it's maybe worth $50-75 tops as is. Don't forget that these are full of rubber covered wire, and it's missing the remote control box, unless the seller has it sitting around and not knowing that it belongs with the radio. According to the gallery it's the same as a 40-205RX/39-55RX chassis, except that they added a pair of shortwave bands. An interesting set because of the remote control but nothing special in terms of performance, basically a five tube radio with a push pull output stage, no extra RF or IF amplifiers.
Regards
Arran
#3

I think Arran pretty much summed it up for me. If you really like the set, I could see paying up to $100. $200? Naah, I would pass and wait for a better one at a lower price.

In fact, if you wait for Radiofest in August, you might find a better one there at 1/4 the price of this one. I do not know if there are any radio clubs in Wisconsin.

--
Ron Ramirez
Ferdinand IN
#4

To be honest I like the cabinet styling of most of these squarish 1939-42 Philco consoles, but if I were going for a remote control set it would have to be one of the /16 series that at least has something in the front end. This is a very average console set with the gimmick of remote control, better then the 40-205RX but not enough to pay top dollar for.
Regards
Arran
#5

Agree with Arran too. For $200 you might find something like 38 or 37-116 that will knock the socks off of the 40-215. Must admit it is a interesting design but a lot of work to get it working right.
GL & Happy New Year!!
Terry
#6

Thanks for the input guys! Arrans thoughts as to price were pretty spot on to mine. I was going to contact the seller and offer him $50 to $75 for it, but after thinking it over, I'm going to pass on it. I've got enough projects as isIcon_lol The only reason it called to me was because it was a Mystery Contol set. By the way Terry I have a 37-116 in the collection, waiting for some attention, but, looking at that chassis, I'm kinda scared to work on it Icon_lol I here they are great performers though!! Thanks again and Happy New Year to everyone!
Kevin
#7

On the 37-116 after you build the stand to hold the chassis upside down that half the battle. The other half is marking everything (wires on the RF deck) so you can get it back together right the first time. The rest is the same old replace all the cap and resistors on the RF deck and the caps on the rest. Check the resistors. Lots of fun!!!!
Terry




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W  1.5k  ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM
Philco 60 Squealing
I have taken out the 2nd IF and found a problem or not. I believe the coils are litz wire. There is a very small strand ...dconant — 02:13 PM
Philco 6K7
I am restoring a Philco 37-60. The am reception is very good, but the shortwave is very weak. Run 6 Philco removes the g...bobbyd1200 — 01:35 PM

[-]
Who's Online
There are currently 4859 online users. [Complete List]
» 4 Member(s) | 4855 Guest(s)
AvatarAvatarAvatarAvatar

>