Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Simple Tube Question?
#1

This question is for a friend and before misleading him I want to make sure I'm correct. This is on a Colonial model 654. AC/DC set.
http://www.nostalgiaair.org/PagesByModel...002860.pdf

On the 1V half wave rectifier the filaments are pins 1 & 4. Filaments shown in the filament chain only on the schematic. My thought is that the top bar on the 1V on the schematic is the plate. But what is the other line going to the first filter cap and the 2K resistor?

I go to the tube data and it appears to be a cathode. But attached to the case of the tube? It's my first time even seeing a 1V rectifier.
http://tdsl.duncanamps.com/show.php?des=1V

Thanks,
Pepperoni

"It's Nice To Be Nice To The Nice"
Major Frank Burns Mash 4077th
#2

The cathode of the 1V is connected to pin 3. The plate (yes, the "top bar" is indeed the plate) connects to pin 2.

I prefer the NJ7P database, specs of the 1V (with drawings) are shown here:
http://www.nj7p.info/Common/Tube/SQL/Tub...hp?Type=1V

--
Ron Ramirez
Ferdinand IN
#3

Thanks Ron! I use the Duncan Amps site and at the bottom of the page (you already know this) there's an "HTML Page" you can click on that takes you right to the nj7p database. And I do like that database better. Gives a bit more info.

Pepperoni

"It's Nice To Be Nice To The Nice"
Major Frank Burns Mash 4077th




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently 2453 online users. [Complete List]
» 2 Member(s) | 2451 Guest(s)
AvatarAvatar

>