Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Bakelite block 3903AH info.
#1

I'm doing a recap on a Philco 80, there is a 3903AH bakelite block that I can't find the lug diagram. I have the list of all available here and it's not there, I believe there is one .01mfd inside but at what terminals. Any help would be appreciated.
#2

A twin 0.09uF. (or 0.1uF, 630 v.) block. Mouting hole Lug #1 and Lug #8 tied together, as you see, is the common for both caps to ground thru the mounting screw obviously. One cap goes to Lug #7, the other to Lug #6. See lug diagram on my site in PARTS section for Bakelite Block Consensers.
#3

I have looked on that chart and it dosen't show a 3903AH. I can do as you said, but am I missing something? does it show it and I don't see it? Thanks for the quick response. Also on my shematic parts list ti shows the 3903AH with a .01mfd. so now i'm really confused.
#4

No, my charts are not all inclusive. Use the info I have above. Use the little bakelite block LUG picture to dertmine the lug numbering scheme.
#5

Chuck, I fully understand the lug pattern, but why , if you could explain for my future referance. If the schematic says in the parts values and part numbers The 3903AH takes a .01mfd and you say use a 0.09mfd twin. Don't know if I'm just thick, but if you could explain I would sleep better at night.
#6

The capacitor in question is item 32 on the schematic:
http://www.nostalgiaair.org/PagesByModel...013843.pdf
It indeed would be .01 and it should be a safety cap since it goes from line to ground.

Carl
Northern Panhandle, WV
#7

I didn't say to use 0.09. That's what the block originally came with. I mentioned that the closest vaule nowadays is 0.1uF in parentheses. Use that value and you'll be fine.
#8

Ok thanks for the help guys. By the way, Just Radios carries the .09uf 630v.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM
Philco Predicta Siesta picture over time getting dimmer
I found that the wire insulation was burnt.  The fly back needs corona dope! Why would someone put that there?Platinumblonde36 — 01:09 AM
Philco Predicta Siesta picture over time getting dimmer
This is what it looked like beforePlatinumblonde36 — 01:01 AM

[-]
Who's Online
There are currently no members online.

>