Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco call letter tabs
#1

I need to replace the tabs by the pushbuttons on my 41-300.Some where pushed way in and one is missing.[ I'm not sure what these things are even called] but they show station call letters by the pushbuttons.like
WGN WIND WLS WBBM. One of them even says TV. I don't know what that was about. anyway I'd like to find a good replacement for them.
thanks.have fun Icon_biggrin
#2

Hi Billvet6,
You can get NOS station call tags on ebay, ex: http://cgi.ebay.com/6577517408

(yes they are Ze----, but you can find official Philco one sometimes too) OR you can make your own, I made some up in MS Word, print them out, spray krylon flat clear on both sides of the paper, then when dry, just cut them out.

I think thats what you were refering too??
take care,
jerry.
#3

thank you for the reply. I will check that out.
#4

Bill,

I think I have some full-size scans of the tab sheet set of 6 pages for a 1942 set somewhere. Can't remember if the color scans are jpegs or pdfs. Once I find the tab set, I'll post here.
#5

thanks Chuck
#6

Found the six jpegs. Each is about 700K in size. Can your email handle 700K attachments? WIll send individually.

Here is a thumbnail of one of the sheets.

[Image: http://www.philcorepairbench.com/images/smalltabs02.jpg]
#7

I don't know. Wish I had asked this question before I sent the check for the papers for the 41 300 from you. These are exactly what I am looking for. Ill certainly try. Thank you so much for the help.
Bill
#8

Will send you the first sheet via email attachment. Let me know if it's ok. If your end has fits, then I'll print out the files on laser and mail to you. Still have your address. No problem. Icon_smile
#9

thanks again Chuck
#10

Chuck
I haven't been able to print these labels. I think our printer has quit.
Bill
#11

Just sent the files to myself at work where I have a nice colour laser (non-smudging when cutting and insert tabs) and will mail them to you on Monday Bill.

Happy Holidays! 8)
#12

I realy thank you so very much.Bill Icon_biggrin
#13

Sooo..... anybody got the tabs that fit the mystery control?
#14

Just caught this thread and find myself in the same boat! Would you be kind enough to email me the call letters? I have a 39-55 that needs numbers. Also, just acquired a 41-300. Will your call letters fit in the push button models?
#15

hyounce Wrote:Just caught this thread and find myself in the same boat! Would you be kind enough to email me the call letters? I have a 39-55 that needs numbers. Also, just acquired a 41-300. Will your call letters fit in the push button models?

I need the same thing!!




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM

[-]
Who's Online
There are currently no members online.

>