Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 40-140T
#1

Well, I figure it's time to post about a Philco radio; so, here's a Philco model 40-140T that I picked up at the flea market. It's was actually sitting on an outside table and playing when I arrived. The owner didn't know what to ask for it. I offered $35 and he said he had more than that in it. With tax, it ended up costing me $58 and some change. I know that was probably a little high; but, had I bought the same radio off ebay or one of the radio forums and factored in shipping cost, it would have probably run close to that amount.

Even though the radio plays, I still wouldn't trust it because it's only had just enough repair to get it going and that looks to have been done a long time ago. Also, someone hacked in a newer speaker and a newer power transformer. Fortunately, I think I have a junk chassis with the correct power transformer and maybe the correct speaker.

I figure that it will be a good performer when it's restored. Here's a video I made of the radio.

http://www.youtube.com/watch?v=5vBV6iZ90Rs
#2

Neat little set, congrats.

radiotvnut Wrote:had I bought the same radio off ebay or one of the radio forums and factored in shipping cost, it would have probably run close to that amount.

And chances are it would have arrived at your home in pieces instead of intact. That's been my luck lately with a couple eBay items...Icon_rolleyes

--
Ron Ramirez
Ferdinand IN




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM

[-]
Who's Online
There are currently 934 online users. [Complete List]
» 2 Member(s) | 932 Guest(s)
AvatarAvatar

>