Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

#1

Picked it up from a friend yesterday. looks to be pretty straight forward. Is there anything about this one I need to know?

One cannot forbid people to be idiots....all one can do is try not to be one. -Morzh
#2

Nothing that I can think of. Just the usual capacitors and resistors.

--
Ron Ramirez
Ferdinand IN
#3

One fly in the ointment. It looks like in the past someone scavenged two of the three square tube shields. They also broke the rivets holding the bases in place and removed them too. Should I source the parts and pop-rivet them into place? I will post an ad in classifieds for the parts.

One cannot forbid people to be idiots....all one can do is try not to be one. -Morzh
#4

6J5, 6A8 and 6K7 are available and are drop in replacements for the "G" types and do not require shields. The socket for pin #1 must however be grounded to the chassis. Be certain that these pins are not used as a convience tie point for unrelated components. The other remaining tubes, 6K5G/GT and 5Y4 do not get shields. Not to confuse you, but if you need a new 6F6G, you can replace with a 6F6 (metal type,) and if so ground Pin #1 as above.
Actually replacing the tubes may be easier and less of a pain than sourcing tube shields, but it's up to you. The metal tubes are more plentiful and cheaper than the G types.

I trust this is your set: Shoot a picture or two.
#5

I will get a couple photos loaded and post a link to my photobucket. Interesting idea about the metal tubes vice sourcing shields. I will consider that, it just so happens I have all the other types in my stash, but only the ST glass.

It's a pretty little tabletop. Finish is a little kicked, but I think I can make it look OK.

One cannot forbid people to be idiots....all one can do is try not to be one. -Morzh
#6

If you can get tube shield bases from a junk 1937 Philco set, they use the square shields but the bases are four flat "fingers" that will allow the use of metal, GT or ST tubes.

Just a thought.

Codefox has a good idea regarding the metal tubes, but bear in mind that if you go all metal with no shields, any future replacements will also have to be metal. When pin 1 is grounded, the metal shell serves as the shield.

--
Ron Ramirez
Ferdinand IN




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
American Bosch Model 802 auto radio
Hello again;   I found a model 838 car radio on Nostalgia Air under United American Bosch, http://www.nostalgiaair.org/...Arran — 09:32 PM
New Philco Repair Bench
Morzh is correct. The repair bench on our website is an archived image of chuck’s original site. He no longer provides s...klondike98 — 05:32 PM
Made mistake & did not label connection
Excellent information. It is all starting to come together now and your explanation really helped since I noticed that ...georgetownjohn — 04:39 PM
Made mistake & did not label connection
Hi John, I don't have this radio, but I can supply some info: Based on your pic, pins 7,8 and 1 are used together, go...MrFixr55 — 02:02 PM
New Philco Repair Bench
As far as I know, the Repairbench does not work, and has not been working in a while. Chuck (we had that campaign looki...morzh — 01:33 PM
Radio city products 664 schematic request
Need a schematic or manual for the 664. The 663 may be similar.daveone23 — 12:38 PM
New Philco Repair Bench
Thanks Gary.dconant — 12:16 PM
New Philco Repair Bench
I tried accessing the site through our library and got the same response. It's reported to our tech gurus. GaryGarySP — 11:50 AM
New Philco Repair Bench
I am sure this is the archive, and not the Chuck's site.morzh — 09:50 PM
Made mistake & did not label connection
It's not like we are good friends with that wire and can tell it from other ptetty identical looking wires. Why'n't you...morzh — 09:49 PM

[-]
Who's Online
There are currently 6197 online users. [Complete List]
» 1 Member(s) | 6196 Guest(s)
Avatar

>