Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Finally got my 40-180 this morning.
#1

This radio was only 20 minutes away, yet took me a week to finally get my schedule to jive with the seller's to go see it. I actually found out about this before my 38-116 after the guy answered my want ad for a 37-116 or 38-116!
I stumble on this and the 41-280 model Philcos quite often around here, but they always have the automatic $100 price tag no matter what they look like. This one was a lot cheaper, but has the usual 40-180 issues. Bad push buttons, bad finish, and it is missing a tube. (The 1235?) One nice thing is it still has all the knobs and I still have to fish two 45 record adaptors out of the grill. I can use those!

   

   

No matter where you go, there you are.
#2

I think I have a good set of pushbuttons if you're interested. Icon_surprised Weren't there 2 different lengths? PM me if you want.
Art
#3

There are actually three types of push buttons. 39's are longer than 40's that slide on with a snug fit. I believe the 41's were short, but needed the little spring clips inside of button to fit snug. Wine Red or Brown. 40-180 usually used the Wine Red which look better when lit than the plain brown ones that don't glow when radio is on.
#4

Out of the three XX-#80 models I prefer the 40-180, if nothing else the ones thing it has going for it is the brass escutcheon and the Bakelite knobs. Reproduction pushbuttons are not hard to come by and are relatively inexpensive.
At one point I was contemplating getting the Canadian version of a 41-280, apparently they do not use as much of that crappy rubber covered wire as the U.S versions do. The problem was it needed everything, knobs, pushbuttons, escutcheon, the lot, and he wanted $80 I think. I suppose if I really wanted it I could have negotiated the price down, but the fact that it needed about $60 of repro parts made me walk away.
Regards
Arran




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM

[-]
Who's Online
There are currently 3792 online users. [Complete List]
» 1 Member(s) | 3791 Guest(s)
Avatar

>