Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Does anyone have any info they could share?
#1

Hi there.

I'm new to the forum so I'm hoping I'm following protocol.

I inherited an old Philco console Radio with a turntable several years ago. The radio was made in the early 50's in Toronto Canada. The model number on the cabinet is 730 which also matches the chassis number on the radio. On the cabinet it says "Model No." and on the metal chassis it says "Chassis No.". Anyhow.. I have searched high and low and cannot find a thing about this unit on the net. I've restored the cabinet but it just won't be right if I can't restore the radio.

I'd appreciate any help you can give me.
#2

Hello and welcome.

I'm afraid I can't help you, since I have very little info on Canadian Philco radios. The Canadian models began to use different model numbers from their US counterparts in 1939, and some Canadian Philcos are quite different than USA models.

So you will need info from someone in Canada, or someone who has Canadian Philco info.

--
Ron Ramirez
Ferdinand IN
#3

There was a post on this forum last year about the same radio:
http://philcoradio.com/phorum/showthread.php?tid=232

Carl
Northern Panhandle, WV
#4

Thanks Carl. Missed that entirely. Icon_redface

--
Ron Ramirez
Ferdinand IN
#5

Thanks a million. Thats the unit! I have a starting place now Icon_biggrin




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Help with Readrite 410 tube tester
I fixed it. The filament selector switch is not that great of quality. Cleaned it and it takes some fiddling with to get...daveone23 — 06:58 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
It's a vacuum tube set and it's over 60 years old.  My uncle acquired it for my parents when Philco was done with it, an...jeibner — 10:24 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
Hi J Eibner, Welcome to the Phorum.  Lots of Phriendly Pholks with Phine (See a pattern here?) advice. It is very...MrFixr55 — 09:54 PM
Philco 89B code 123 newbie
Or you can do what Terry suggests. Thx Terry for remembering that. A lot cheaper. I remember an article about that, b...MrFixr55 — 09:07 PM
Philco 48-200 alignment questions
Thanks to everybody for all the info so far. RodB, thanks for the additional info. I worked on this radio years ago a...transitony — 08:40 PM
Philco 89B code 123 newbie
Now that I've been thinking about it somewhere I saw a replacement made using a section of pvc pipe and a cap to cover t...Radioroslyn — 08:25 PM
Philco 48-200 alignment questions
Terry's gimmick cap is two insulated wires twisted together about 2 inches long, one wire attaches to the generator outp...RodB — 07:46 PM
Philco 48-200 alignment questions
Hi, in this case I would be certain that pin 7, which is B-, of the 14A7 is not "hot". If it is then reverse t...RodB — 07:39 PM
Philco 48-200 alignment questions
Yup. The gimmick is to take the place of the 100mmfd cap you don't have.Radioroslyn — 07:34 PM
Philco 48-200 alignment questions
Thanks for the reply Terry. Yes I am definitely using an isolation transformer. If I work with your method and connec...transitony — 07:29 PM

[-]
Who's Online
There are currently 1520 online users. [Complete List]
» 1 Member(s) | 1519 Guest(s)
Avatar

>