Philco 38-62 cabinet restoration
Posts: 804
Threads: 42
Joined: Dec 2008
City: Chicago, IL
Posts: 7,294
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Boy that did clean up really nice!!
Terry
Posts: 4,816
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA
What sort of bleach did you use, was it just the common sodium hypochlorate bleach like you find under the kitchen sink? I've found that you can get rid of the black stains in some woods with phosphoric acid, which leads me to think that they are iron stains.
Regards
Arran
Posts: 804
Threads: 42
Joined: Dec 2008
City: Chicago, IL
Just common bleach. I think it was water stains and mildew on this cabinet.
(This post was last modified: 04-12-2013, 01:12 PM by Bob Andersen.)
Posts: 804
Threads: 42
Joined: Dec 2008
City: Chicago, IL
Time for grain filler. I used Constantines thinned a little with mineral spirits. After it dried to a haze, I scraped off the excess with a credit card.
It's a bit too light in the middle of the top from the bleaching. I hope to blend that out with toner.
[Image: http://farm9.staticflickr.com/8536/86437...ef8a_c.jpg]
[Image: http://farm9.staticflickr.com/8245/86426...781b_c.jpg]
(This post was last modified: 04-12-2013, 02:38 PM by Bob Andersen.)
Posts: 163
Threads: 8
Joined: Jun 2011
City: Chicago,illinois
Bob...it's getting there. Nice work!
Posts: 804
Threads: 42
Joined: Dec 2008
City: Chicago, IL
Thanks. I just sprayed on some sanding sealing and a few coats of Medium Brown Walnut toner lacquer.
I thought it looked pretty good, but now that I've compared it to the original photos I think it's a little too light 
[Image: http://farm9.staticflickr.com/8254/86525...e798_c.jpg]
(This post was last modified: 04-15-2013, 06:04 PM by Bob Andersen.)
Posts: 4,816
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA
I thought that they may have used something close to extra dark walnut toner like the 1936 Philco tombstones used, it looks like they used a similar junk wood for the top and sides of the cabinet. Maybe it was perfect brown toner?
Regards
Arran
(This post was last modified: 04-15-2013, 08:10 PM by Arran.)
Posts: 804
Threads: 42
Joined: Dec 2008
City: Chicago, IL
The traces of original finish left weren't quite so dark or opaque as my mid-30s tombstones. I do have some dye based extra dark walnut lacquer though and I'll give it a try tomorrow.
Posts: 7,294
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Starting to look pretty super there Dynamo Bob!!!
GREAT JOB!!
Terry
Posts: 804
Threads: 42
Joined: Dec 2008
City: Chicago, IL
Thanks Terry and good call Arran. The extra dark walnut looks much better  It's a rich, dark brown and you can still see hints of the grain. That just leaves the trim.
[Image: http://farm9.staticflickr.com/8122/86560...9927_c.jpg]
(This post was last modified: 04-16-2013, 02:14 PM by Bob Andersen.)
Posts: 163
Threads: 8
Joined: Jun 2011
City: Chicago,illinois
WOW...That's looking great! Can't wait to see it done.
Posts: 5,129
Threads: 271
Joined: Nov 2012
City: Wilsonville
State, Province, Country: OR
wow! very nice 
Posts: 804
Threads: 42
Joined: Dec 2008
City: Chicago, IL
I wrapped up the toner and put on a couple coats of clear gloss this afternoon. I knew I was taking a chance because of the high humidity levels, but I really wanted to get it done.
Luckily, just a minimal amount of blushing in the clear coat that I expect will sand out.
[Image: http://farm9.staticflickr.com/8265/86618...9143_c.jpg]
The scar where I repaired the split is barely visible in very bright light.
[Image: http://farm9.staticflickr.com/8241/86607...658a_c.jpg]
I'll let it cure for a week or two, then sand with 600 grit and spray on a couple more coats.
If I had to do it again, I would have gone a little bit lighter on the body. Maybe one or two less coats of the extra dark walnut.
[Image: http://farm9.staticflickr.com/8246/86607...3a8c_c.jpg]
(This post was last modified: 04-18-2013, 07:00 PM by Bob Andersen.)
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
WOW  
Bob, do you have any Mohawk No Blush Plus? It's great for getting rid of the blushing. Just spray a little on the area where the lacquer has blushed, and the blushing magically disappears!
--
Ron Ramirez
Ferdinand IN
Users browsing this thread: 1 Guest(s)
|
|
Recent Posts
|
|
An attempt to remove the Field Coil from a G speaker
|
| Mike;
I've only run into a speaker with an open filed coil twice, and they were on newer speakers from the 1940s. One ...Arran — 12:48 AM |
|
An attempt to remove the Field Coil from a G speaker
|
| Arran
Yes, this is my plan for now and what do I got to lose, this is not even the speaker from this radio, but one o...morzh — 10:44 PM |
|
An attempt to remove the Field Coil from a G speaker
|
| Mike;
I would unwrap the field coil, and see if maybe there a break near one of the ends, like where the coil wire att...Arran — 10:23 PM |
|
An attempt to remove the Field Coil from a G speaker
|
| ...and this is what I did. I fed a little LT into the screwholes with a small brush, and a little on the rim next to the...morzh — 09:52 PM |
|
Philco 40-120C Restoration
|
| I combined the two 40-120C threads together as we like to keep the discussion of the same radio together. It helps with...klondike98 — 09:36 PM |
|
Philco 40-120C Weak, Distorted Ouput
|
| Just checked were I buy tubes price is four dollars. So living in Florid we have a local source for tubes. David David — 09:14 PM |
|
Philco 40-120C Weak, Distorted Ouput
|
| The higher voltage may be due to higher mains voltage. My mains run 120-125AC when the set was new mains would be 110-11...David — 09:09 PM |
|
Philco 40-120C Weak, Distorted Ouput
|
| Thank you for your reply. I pulled a speaker from a Philco 41-221 and received the same result. I used a signal tracer t...bluecap — 08:45 PM |
|
Philco 40-120C Weak, Distorted Ouput
|
| Have you tried a different speaker?
How did you trace the distortion?
How do you know it is weak? What is the reference?...morzh — 08:33 PM |
|
Philco 46-480 Electronic Restoration
|
| Amen to that! Every time I think I’ve captured them all, I realize that there’s another error. My goal is to finish with...jrblasde — 07:00 PM |
|
Who's Online
|
There are currently 2820 online users. [Complete List]
» 2 Member(s) | 2818 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
