Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

A rediscovered Silvertone
#1

A call from my mom last week saying the bathroom sink wouldn't drain, led to a Saturday in the basement of their home replacing dwv lines for me!!! What fun!! Anyway, a lot of the sets from my early days of collecting reside in that basement. This one was off in a corner all but forgotten until I rediscovered it yesterdayIcon_clap So after cleaning up this morning, I dragged it out of there and brought it home! It's just like getting a new find except I didn't have to pay anything for it!!!!!
It's a Silvertone 4586, a ten tube set which, as I remember, didn't cost me anything back in the late '80s either. My mom found this one sitting by the curb for garbage pick up, so she loaded it up and brought it home for me! This was quite a big deal, as my mom wasn't very fond of my hobby in those daysIcon_lol
So, here it is at it's new home.
[Image: http://i1160.photobucket.com/albums/q500...5618f4.jpg]
[Image: http://i1160.photobucket.com/albums/q500...7b544e.jpg]
[Image: http://i1160.photobucket.com/albums/q500...c29262.jpg]
[Image: http://i1160.photobucket.com/albums/q500...4c486c.jpg]
#2

Looks like a good rediscovery.I really like that dial face. Are you going to restore it? MIke
#3

Appears to be a 1936 model.... found a video of one on YouTube:
https://www.youtube.com/watch?v=lUdQNSozAD8


I love the "magic" green tuning eyes those Silvertones used. My 1938 has one too... a 6U5 tube I believe (going by memory).

This is my set: https://www.youtube.com/watch?v=se21DYYGqTg

Greg V.
West Bend, WI
Member WARCI.org
#4

That dial's a real eye catcher. Nice.
#5

Boy that MOM is a KEEPER!!!
Nice set!
Terry
#6

NostalgiaRadioTime,

That radio looks so much like this one, but it's a bit different. The dial is different, with the broadcast band in the inner ring, instead of the outer ring like this one. Interesting difference...
#7

You're right Brenda! I hadn't looked that closely at the dial. Good eye!

Greg V.
West Bend, WI
Member WARCI.org
#8

BrendaAnnD,
I did a little research on this model Silvertone. Turns out that Silvertone used two different chassis types manufactured by two different companies. one by Colonial and the other by Stewart-Warner, which accounts for the slight differences in the dials due to tracking. Also the Stewart-Warner chassis has the tuning knob off to the right, whereas the Colonial chassis tuning knob is directly below the dial. My silvertone has the Colonial make chassis.
Mike,
I do intend on fully restoring this set. it will be quite a challenge though, as the cabinet has quite a few issues, i.e. loose joints, delamination on the sides and missing veneer. It is a very attractive radio and well worth the effort to bring her back.
Kevin
#9

Hope you can find time to post some pics as you go through the set. Good luck. Mike




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Made mistake & did not label connection
Hi John, I don't have this radio, but I can supply some info: Based on your pic, pins 7,8 and 1 are used together, go...MrFixr55 — 02:02 PM
New Philco Repair Bench
As far as I know, the Repairbench does not work, and has not been working in a while. Chuck (we had that campaign looki...morzh — 01:33 PM
Radio city products 664 schematic request
Need a schematic or manual for the 664. The 663 may be similar.daveone23 — 12:38 PM
New Philco Repair Bench
Thanks Gary.dconant — 12:16 PM
New Philco Repair Bench
I tried accessing the site through our library and got the same response. It's reported to our tech gurus. GaryGarySP — 11:50 AM
New Philco Repair Bench
I am sure this is the archive, and not the Chuck's site.morzh — 09:50 PM
Made mistake & did not label connection
It's not like we are good friends with that wire and can tell it from other ptetty identical looking wires. Why'n't you...morzh — 09:49 PM
Made mistake & did not label connection
I'm not sure why that wire wasn't covered in the video. I'm pretty sure the 6A8 won't work until that pin is grounded. Y...RodB — 09:47 PM
Made mistake & did not label connection
You'll have to forgive me, I am not sure what you mean.  Can you explain what you are really saying.  If anyone does not...georgetownjohn — 08:05 PM
Made mistake & did not label connection
Those are details better left to the ones who know. Maybe you disconnected the wrong end of the wire.RodB — 06:22 PM

[-]
Who's Online
There are currently 4907 online users. [Complete List]
» 2 Member(s) | 4905 Guest(s)
AvatarAvatar

>