Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

37-610
#16

+1 what Arran says. If I'm goingf to spend a considerable amount on a radio, I prefer natural wood grain every time! Take care. Gary

"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan
#17

I have many sets in cabinets that are mezza-mezza but play well and had a clean chassis to work with. Though a nice shelf Queen is pretty too. Where I like to listen to the radios I live with the the water stains, cigarette burns, maybe refinish when really poor....
Good Hunting.

Paul

Tubetalk1
#18

I have a 37-610 ..Just because its only five tubes do not even think for a minute that you should not purchase to put into your collection. It is super picks up stations from all over. I love mine would not give it up. My faux wood grain has two very little scratches. One of the very first radios I ever purchased. Keith Park did the electronic resto thats why it works go good. I am still trying to get the handle of doing one myself.
#19

I don't believe Arran meant to slam the 610!

I have owned several 610s and 37-610s, and agree that they do very well for a five-tuber. Philco made some swell five-tube sets!

But relatively speaking, for 200 dollars you can get a lot of radio. From a standpoint of sensitivity, selectivity, and quality volume, the 610 does not perform as well as other models with more tubes/features that you could get for 200 dollars. In fact, I got my 37-116 for 200, and my 38-116 for less, and both are in nice shape.

The 610/37-610 was closer to a base model set, albeit a good playing one.

The 200 dollars spent on the 37-610 was doubtless due to it's condition. For many folks that is what they are looking for.
#20

$200.00 dollars is a whole lot to pay for that radio... but is a good performer for a five tube radio.
#21

No I wasn't bashing the 37-610 in and of itself, I just wouldn't think of paying $200 for one just because the faux grain is in nice shape. Because these sets were a near entry level model there were a lot of them produced. While the faux grain is bad on a lot of them it's not like it's anywhere near impossible to find one where the grain, if not pristine, is at least restorable like the front panel on Bob's 38-62.
Regards
Arran
#22

+1 Icon_thumbup




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM

[-]
Who's Online
There are currently no members online.

>