Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

37-610
#16

+1 what Arran says. If I'm goingf to spend a considerable amount on a radio, I prefer natural wood grain every time! Take care. Gary

"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan
#17

I have many sets in cabinets that are mezza-mezza but play well and had a clean chassis to work with. Though a nice shelf Queen is pretty too. Where I like to listen to the radios I live with the the water stains, cigarette burns, maybe refinish when really poor....
Good Hunting.

Paul

Tubetalk1
#18

I have a 37-610 ..Just because its only five tubes do not even think for a minute that you should not purchase to put into your collection. It is super picks up stations from all over. I love mine would not give it up. My faux wood grain has two very little scratches. One of the very first radios I ever purchased. Keith Park did the electronic resto thats why it works go good. I am still trying to get the handle of doing one myself.
#19

I don't believe Arran meant to slam the 610!

I have owned several 610s and 37-610s, and agree that they do very well for a five-tuber. Philco made some swell five-tube sets!

But relatively speaking, for 200 dollars you can get a lot of radio. From a standpoint of sensitivity, selectivity, and quality volume, the 610 does not perform as well as other models with more tubes/features that you could get for 200 dollars. In fact, I got my 37-116 for 200, and my 38-116 for less, and both are in nice shape.

The 610/37-610 was closer to a base model set, albeit a good playing one.

The 200 dollars spent on the 37-610 was doubtless due to it's condition. For many folks that is what they are looking for.
#20

$200.00 dollars is a whole lot to pay for that radio... but is a good performer for a five tube radio.
#21

No I wasn't bashing the 37-610 in and of itself, I just wouldn't think of paying $200 for one just because the faux grain is in nice shape. Because these sets were a near entry level model there were a lot of them produced. While the faux grain is bad on a lot of them it's not like it's anywhere near impossible to find one where the grain, if not pristine, is at least restorable like the front panel on Bob's 38-62.
Regards
Arran
#22

+1 Icon_thumbup




Users browsing this thread: 6 Guest(s)
[-]
Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

[-]
Who's Online
There are currently no members online.

>