1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Tube bloat in an RCA?
BrendaAnnD
Phorum Expert
*****
Posts: 1,108
Threads: 89
Joined: Jun 2011
City: Tacoma State, Province, Country: Washington
#16

06-10-2013, 08:09 PM
Looking through Beitman's early Crosley sets, the ones with the most bloat and convoluted circuitry I think I've ever seen are the model 160 and 171, each with 12 tubes.
Find
Jayce
Phorum Expert
*****
Posts: 2,026
Threads: 367
Joined: Jun 2010
City: Dover, OH
#17

06-10-2013, 08:59 PM
Well, I seem to be in a major holding pattern on this radio and a few other deals, including three radios I am trying to sell. Might end up having to throw in the towel and persue other interests for a bit.
No matter where you go, there you are.
Find
Paul Philco322
Super Moderator
******
Posts: 4,381
Threads: 412
Joined: Jun 2011
City: Boston State, Province, Country: Massachusetts
#18

06-10-2013, 09:07 PM
I have seen several Crosleys I have thought were aesthetically pleasing to view but have not had the confidence in the innards to go for it. I have to keep looking. If the tube set up does seriously contribute to performance why bother. Like those old ads, "6 tubes provide 8 tube performance" they said that to think you were getting a hot set. On the other hand just cause a set has 10 tubes it can still be a clunker.

Paul
Tubetalk1
Website Find
TA Forbes
Deviate Emeritus
*****
Posts: 2,353
Threads: 92
Joined: May 2010
City: Clayton, NC
#19

06-12-2013, 03:40 PM
The D-22 is quite a set!

One thing I have always wondered about is why resort to a 2V tube when there were very good 6V tubes available?

Both the 6A3 and 6B4G are considered equivalent to the 2A3 in the RCA RC-17 manual.
Additionally, 6L6 tubes were available.
Find
« Next Oldest | Next Newest »




Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 4726 online users. [Complete List]
» 1 Member(s) | 4725 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)