Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

49-1401 Boomerang
#1

This was an interesting set to restore... instead of sliding a chassis out of the back of a cabinet, this one lifts out the top! And the phonograph chassis & front door assembly are all part of one chassis! You have to unscrew a piece of wood trim over the door to be able to lift the chassis out. Anyhow, here are some heavily flashed photos of how it turned out....

   

   

Freshly flocked turntable visible through the slot. I'm becoming quite the little flocker! Icon_lol
   

   

   

Greg V.
West Bend, WI
Member WARCI.org
#2

That's a neat looking set. Nice job on the restore!
#3

There is a hustler in my area of the world who has one of those and has been trying to sell it on craigslist for some outrageous price for at least four years. Currently he's also trying to sell a Predicta Princess model for $1300 with a boatload of hack repairs in it, what he calls a "restoration" He used to frequent the alternative forum until he wore out his welcome over there playing the "I'm just a fellow collector" routine bumming parts and schematics from people.
It's an interesting set to be sure, an updated version of a 46-1201, but unlike the 1201s I don't think they were made for more then a year or so. Unlike the the 1201s it looks like most of the wood parts of the cabinet used real veneer instead of that faux finish that likes to flake off. Speaking of flocking my model 76's (46-1201) platter could use a similar reflocking, and a cartridge rebuild, and the mercury tilt switch also needs attention.
Regards
Arran




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently 1843 online users. [Complete List]
» 2 Member(s) | 1841 Guest(s)
AvatarAvatar

>