Posts: 2,026
Threads: 367
Joined: Jun 2010
City: Dover, OH
Here is the Emerson console radio I purchased earlier today. It will definitely need work and the guy was lucky he didn't start a fire by trying to play it! The underside of the chassis was crammed full of stuff from chipmunks! Anyways, it is a seven tube console and the tube compliment is: 80, 47, 2A6, 58, 58, 58, 56. The speaker is a Utah speaker that looks to weigh more than the chassis. I can't find a model number on this unit, just a serial tag on the chassis.
No matter where you go, there you are.
Posts: 1,108
Threads: 89
Joined: Jun 2011
City: Tacoma
State, Province, Country: Washington
I believe this may be your beastie..
http://www.nostalgiaair.org/PagesByModel...004742.pdf Emerson Model 77
Posts: 2,026
Threads: 367
Joined: Jun 2010
City: Dover, OH
That looks like it! Thanks! 
No matter where you go, there you are.
Posts: 3,135
Threads: 54
Joined: Apr 2011
City: Lexington, KY
Yep, it looks like a 77.
[Image: http://img.photobucket.com/albums/v348/j...rson77.jpg]
Nice snag, there aren't a whole lot of Emerson consoles floating around out there.
John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
Posts: 2,026
Threads: 367
Joined: Jun 2010
City: Dover, OH
Thanks for the advertisement picture, Elliot! So far I have not stumbled on any pictures of existing model 77 consoles, just pictures taken from advertisements like that one. I would not have gone for this radio if it hadn't been such a rare piece. I know where two slightly later Emerson consoles are sitting in storage, but have been afraid to ask the guy what he wants for them. Both are in nice shape.
No matter where you go, there you are.
Posts: 4,703
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
Judging by the schematic it looks like a fairly straightforward radio to work on, a single band and about ten paper caps and two electrolytics to replace. It also has a tuned RF amplifier stage so it's probably a reasonable performer. I think the biggest issue will be repairing or replicating that grille, but it looks like the front panel could be removed to work on it.
Regards
Arran
Posts: 1,108
Threads: 89
Joined: Jun 2011
City: Tacoma
State, Province, Country: Washington
Jayce,
Be sure to send a pic of this rare set to Radio Attic Archives.
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
That's where I looked and couldn't find it.
Terry
Posts: 1,108
Threads: 89
Joined: Jun 2011
City: Tacoma
State, Province, Country: Washington
But if he sends the pic, it will be there for the next person. 
Posts: 2,026
Threads: 367
Joined: Jun 2010
City: Dover, OH
Hmm, I will have to check the site out and do that. Hope they don't mind a picture of a sort of rough looking Emerson.
No matter where you go, there you are.
Posts: 2,353
Threads: 92
Joined: May 2010
City: Clayton, NC
That's a nice snag, Jay!!!
Although I hate to say "I told you so," I am going to do it anyway!
Radios ALWAYS come around. A couple of months ago you were not having any good luck. NOW you ARE!!!!
 
Users browsing this thread: 1 Guest(s)
|
|
Recent Posts
|
|
Shadow Meter Bulb
|
| Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM |
|
Philco 41-608 changer coupler
|
| 3D-printing...short of machining, of course.
Or molding.morzh — 05:20 PM |
|
Philco 41-608 changer coupler
|
| Thanks, Morzh.
That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM |
|
12' Philco
|
| If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel.
Kareem would have an e...morzh — 01:48 PM |
|
12' Philco
|
| And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM |
|
Hickok AC51 tube tester
|
| I think they have only shown the secondaries of the transformer.
Two of them feed the rectifiers' filaments.morzh — 12:58 PM |
|
IF can wire size and Rubber mounts?
|
| Arran
If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM |
|
12' Philco
|
| Rod,
Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently.
H...morzh — 12:54 PM |
|
Hickok AC51 tube tester
|
| Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM |
|
IF can wire size and Rubber mounts?
|
| Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM |
|
Who's Online
|
There are currently 4861 online users. [Complete List]
» 1 Member(s) | 4860 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
