Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Restore a 37-610
#1

Hello all! I just wanted to firstly state that I am very new to radio restoration and want to say thank you in advance to any and all help that I receive. With that said, I have come into possession of a Philco 37-610 radio. At least that is what the the sticker on the inside of the cabinet claims. It appears to be a 37-623J cabinet, however. Anyways, I came into possession of this after my grandfather had passed. I would ultimately like to at least restore the cabinet for my grandmother as a gift. I believe that the electronic aspect may be a bit past me as it appears the components are in pretty poor shape.
Where could I find the knobs for this cabinet and a new grill cloth? Also, what's the best way to clean the dial (I know thats not the term, very new)? Again, thanks in advance and I am very excited to start learning about this new hobby!
#2

Are you near any of the meets? There is one this weekend in Huntington West Virginia where you cand find knobs and parts also those knobs are reproduced look on tubes and Moore.com and like sites. As for the dial there was a post on here that said mineral spirits will clean the dial without removing the numbers. Good luck finding grill cloth, reproductions have dried up.
#3

check out this site.I just found it myself! I hope it helps. http://web.archive.org/web/2005110310030...index.html
#4

Grillecloth.com (Radio Grille Cloth Headquarters) is out of business.

--
Ron Ramirez
Ferdinand IN
#5

A good place to start for finding knobs is the page on PhilcoRadio: http://www.philcoradio.com/resourceb.htm#l .
#6

Thanks for the advice guys! I think I will just plug away and try to find some knobs on the site Bob provided while periodically checking out eBay and Craigslist.
Is there anyway to find a list of where these meets are that Tab suggested I look into?
Also, I found this grill cloth on RadioDaze http://www.radiodaze.com/product/12906.aspx - is that the right one?
#7

Yes that's it I'm glad to see someone is selling at least some cloth. Todd




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
I think after all has been said, I will use the same bulb that is specified for the dial pilot light which is a #55. I ...georgetownjohn — 07:31 PM
12' Philco
There was also this Philco! klondike98 — 07:25 PM
HiFi (Chifi) tube amp build - but my own design.
I expected a challenge and this is just part of it. But, it's also supposed to be fun, entertaining, informative and enj...TV MAN — 07:12 PM
Shadow Meter Bulb
Butting in here with a question. Since the shadow meter is connected directly to the 1st and 2nd I.F.'s wouldn't the met...RossH — 06:43 PM
HiFi (Chifi) tube amp build - but my own design.
Mike, Tim; you are about to enter the twilight zone. Doo doo doo doo, doo doo doo doo This is something alright. I'm go...RodB — 06:26 PM
HiFi (Chifi) tube amp build - but my own design.
:lol: We need to start a singing radio group! I play the guitar, so maybe get a few vocals? Anyways, Mike, I did try mou...TV MAN — 05:56 PM
HiFi (Chifi) tube amp build - but my own design.
And so does a barber shop quartet. mmmmmmRodB — 03:54 PM
Shadow Meter Bulb
I did try an LED bulb in place of the original but wasn't impressed with the amount of light on the dial. Seems like it ...RodB — 03:51 PM
HiFi (Chifi) tube amp build - but my own design.
Tim Would mounting he transformer vertically change the hum, if used without additional parts? Also, in these amps...morzh — 02:25 PM
Shadow Meter Bulb
Gary I doubt it would introduce any noise. We use similar lamps for the panel indication, 12V AC lamps: they are LEDs...morzh — 02:15 PM

[-]
Who's Online
There are currently 6138 online users. [Complete List]
» 1 Member(s) | 6137 Guest(s)
Avatar

>