Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 60L - Decal
#1

Hello,
I'm restoring a Philco 60 Lowboy, Canadian version.
The cabinet had already been stripped and I'm looking to reproduce the Philco decal. While I've seen that some are available commercially, from looking at other posting, there seems to be some question as to who gets them right. Since I already doing decals, I'd like to reproduce this one as well ( unless I can get a good commercial match.

So, would anyone know the correct size for this label or even, maybe a picture of an original. Ron posted some Philco label pictures on another post, I'm not sure if these would apply to my model.

Thanks for the help,
Daniel
#2

Hi Daniel

Here are a couple of the posts you mentioned.
http://philcoradio.com/phorum/showthread.php?tid=104
http://philcoradio.com/phorum/showthread.php?tid=529

The original decal used on your Model 60L was 1-1/2" long, and would have looked like this (image shown from a 645B tombstone, same decal):
[Image: http://i326.photobucket.com/albums/k420/...decal1.jpg]

Radio Daze offers the PH8 decal shown below, which is not exactly like the original.
[Image: http://i326.photobucket.com/albums/k420/...decal2.jpg]

--
Ron Ramirez
Ferdinand IN
#3

Thanks Ron for the info. BTW your article on the model 60 schematic variation is very well done and really get the confusion out. I really appreciate it.

I have one last question regarding the age of the radio. On your site I found reference to the 60L from January 1934, and on the evolution of the model 60 page, it indicates an introduction date as July 1933 but on my nameplate I find a patent date as 1930. So was this model produced in 1930 ?
Regards
Daniel
#4

No, the Model 60 had not even been thought of in 1930. The first Model 60 sets came out in July 1933, as shown on my website.

Patent numbers shown on those Philco patent labels can predate the actual manufacture of the radio by years; sometimes a patent could be several years older than the radio itself. For example, Edwin Howard Armstrong invented the superheterodyne circuit during World War I, but it did not come into general use until 1930.

--
Ron Ramirez
Ferdinand IN




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Correct model 84 Ac plug an cord type
From what I read Philco went to using brown rubber power cords in 1936, so cloth was used in the 1935 and earlier models...Arran — 11:25 PM
Correct model 84 Ac plug an cord type
Hi Bruce, I have not worked on an 84, but in general, power cords for almost any radio prior to 1938 was cloth covered...MrFixr55 — 08:34 PM
Restoring Philco 38-14
OK, well, so after staring at the sch again, I realized the problem had to be the #12/12A padder. I put a scope on the o...morzh — 08:15 PM
Correct model 84 Ac plug an cord type
Hello Bruce, I mostly use brown far as my cloth powercords go ! Here is the plug that I have used bakelite Acorn style...radiorich — 08:05 PM
Correct model 84 Ac plug an cord type
Looking for as correct as can find the right Ac plug an the correct colored cloth line. Ive seen many old photos but mos...Bruce — 04:13 PM
Restoring Philco 38-14
Rod Two Y-caps make sense if you use them from L/N to the chassis; this is only makes sense in the transformer radios...morzh — 10:11 AM
Restoring Philco 38-14
Mike, I'm curious about a specific use of he Y cap. Lately I've seen a single cap across the power transformer primary. ...RodB — 09:01 AM
Restoring Philco 38-14
hello morzh , That sounds like a plan ! Sincerely Richardradiorich — 07:45 AM
Restoring Philco 38-14
Richard, It helped some, but I still had the whining when engaging the rear power strip (I did not realize it was fro...morzh — 07:07 AM
Restoring Philco 38-14
Hello morzh, Yes , that dreaded hum in my room where i do alighment I have my cable modem and router plus desktop plus ...radiorich — 11:25 PM

[-]
Who's Online
There are currently 4019 online users. [Complete List]
» 1 Member(s) | 4018 Guest(s)
Avatar

>