Posts: 825
Threads: 113
Joined: Aug 2012
City: The Villages
State, Province, Country: Florida
Every time I think I know what I'm doing, I get hit with something like this. (Although, once I solve the problem I sure feel great)
OK, 38-12. The motorboating is a putt-putt sound, about 2 per second. In other words not real fast. Doesn't change with volume or station position. It was there before I did anything.
What I've done so far: All tubes tested and replaced 78 and 6A7. All caps replaced. All micas tested, within specs. All resistors tested and almost all replaced. All coils and transformers tested ok. I can put a signal to the center terminal on the volume control and it comes in loud and clear, along with the putt-putt.
All voltages check ok except one. The screen (S) voltage on the 78 tube should be 90v and I have 27v.
So now I'm stuck. Any ideas?
http://www.nostalgiaair.org/PagesByModel...013236.pdf
Thanks.
Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org
(This post was last modified: 08-21-2013, 11:26 AM by Eric Adams.)
Posts: 2,128
Threads: 18
Joined: Oct 2008
City: Merrick, Long Island, NY
9 out of 10 times it is a flaw in the voltage divider, and then usually a filter capacitor, crispy critter resistor, or a missing tube shield. Of course that is if you did not change orientation of components when replacing ancient capacitors. Start there.
Posts: 825
Threads: 113
Joined: Aug 2012
City: The Villages
State, Province, Country: Florida
Thanks, just what is the voltage divider? Filter caps are new, resistors were checked and replaced as necessary. It doesn't have tube shields. Since it made the sound before I touched it, I doubt that the orientation of components is the issue.
Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org
Posts: 2,128
Threads: 18
Joined: Oct 2008
City: Merrick, Long Island, NY
Other (tubular caps ) replaced ? Voltage divider is chain of resistors and capacitors used to isolate stages and eliminate interference with each other. Plenty of stuff on line about that and motor boating as well. Obscure causes too!. Best!
Posts: 293
Threads: 55
Joined: Mar 2007
City: Toledo
State, Province, Country: OH
There should be a shield around the 6A7.
Posts: 825
Threads: 113
Joined: Aug 2012
City: The Villages
State, Province, Country: Florida
As I stated, all of the caps have been replaced. Can you give me a place to look? Like what is the voltage divider on the 38-12? I looked on line but I still don't know what to look for on this specific radio.
http://www.nostalgiaair.org/PagesByModel...013236.pdf
Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org
Posts: 825
Threads: 113
Joined: Aug 2012
City: The Villages
State, Province, Country: Florida
actually, the shield is on the 75, but that isn't the problem. The problem was my screw up. It is working now. 
I think I need a vacation!
Thanks for your input.
Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
So, what happened, and what did you do to correct the issue?
--
Ron Ramirez
Ferdinand IN
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
Yes Eric, let us know what you did. This is how we learn.
Jerry
A friend in need is a pest! Bill Slee ca 1970.
Posts: 825
Threads: 113
Joined: Aug 2012
City: The Villages
State, Province, Country: Florida
Ok guys. I'd rather not say. but I will tell you that a 75 tube will fit in an 84 socket and a 38-12 only uses 1 75 tube! 
Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org
Posts: 15,511
Threads: 544
Joined: Oct 2011
City: Jackson, NJ
OK, I guess this is where "the more the better" does not apply
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
Thanks Eric, I think most of us have done something like that and a good reminder to check!
Jerry
A friend in need is a pest! Bill Slee ca 1970.
Posts: 825
Threads: 113
Joined: Aug 2012
City: The Villages
State, Province, Country: Florida
Yup! At least the good news is that after all the testing/replacements the radio really sounds good!
Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org
Users browsing this thread: 2 Guest(s)
|
|
Recent Posts
|
|
AC/DC Transformer-less Sets
|
| Joseph,
Thank you for the confirmation. I knew that there must be more to the Transformer-less AC/DC radios than the ...PeterN — 10:30 PM |
|
AC/DC Transformer-less Sets
|
| Good evening, folks. Power station engineer here!
The east coast had pockets of DC-only power well into the twentieth...jrblasde — 10:11 PM |
|
AC/DC Transformer-less Sets
|
|
Model 40 does not have a rectifier, so it would be a DC only model.
This however does not say anything about using...morzh — 08:01 PM |
|
AC/DC Transformer-less Sets
|
| I was wondering if anyone knows if these AC/DC transformer-less sets were actually used on 110v DC anywhere, and when.
...PeterN — 06:35 PM |
|
Looking for place to donate unique Philco Philco J-1930 Prototype
|
| Given the 1960s vintage, it is likely that the cartridge is ceramic, likely more stable. The changer looks like a Voice...MrFixr55 — 05:03 PM |
|
Jackson 665 j2 schematic request
|
| FIXED!daveone23 — 03:55 PM |
|
Bakelite crack repair - what is best epoxy?
|
| Thanks everyone. I appreciate you sharing your experience and looks like I'll work with the 24 hr two part clear epoxy....de371 — 10:25 PM |
|
Jackson 665 j2 schematic request
|
| Without a schematic its going to be hard tracing the wire wound spool resistors.daveone23 — 05:21 PM |
|
Jackson 665 j2 schematic request
|
| Looking for a schematic for the 665 j2 multimeter.daveone23 — 04:42 PM |
|
Looking for place to donate unique Philco Philco J-1930 Prototype
|
| >>I'll write to the Henry Ford.
I heard, his secretary answers his mail, not he himself.morzh — 12:15 PM |
|
Who's Online
|
There are currently 2916 online users. [Complete List]
» 1 Member(s) | 2915 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
