Posts: 56
Threads: 15
Joined: Jan 2013
City: Felton, PA
Looking at replacing the 4 by-pass caps in the box (part#46).
http://www.nostalgiaair.org/PagesByModel...013125.pdf
It contains three 1uF's and a 2uF. Parts list calls for electrolytics. Do they need to be electrolytics? Seems to me that mylars would be a better choice.
Any input?
(This post was last modified: 09-12-2013, 03:48 PM by
hunter2115.)
Posts: 7,248
Threads: 266
Joined: Dec 2009
City: Roslyn Pa
I'd go with mylars. Shouldn't matter either way.
Terry
Posts: 1,114
Threads: 14
Joined: Feb 2013
City: Irvington, NY
I am also rebuilding the 118 multisection cap right now and mylars are the way to go, especially since several sections are used as RF bypasses. There is plenty of room inside to fit the tubular style mylars.
You can drill a tiny hole next to each of the cap terminals to pass the lead from the replacement cap and then solder it to the respective terminal. The lead from the common ground end can be passed out at the base under the clamp and connected there.
Posts: 56
Threads: 15
Joined: Jan 2013
City: Felton, PA
I like the idea of using mylars- no need to replace in say, another 80 years??
They are of different voltages. What voltage caps are you using?
Posts: 2,353
Threads: 92
Joined: May 2010
City: Clayton, NC
Mylar caps get pretty big compared to electolytics for values larger than .5 uFd.
Posts: 1,114
Threads: 14
Joined: Feb 2013
City: Irvington, NY
I am using 400V caps because that is what happen to have. I would prefer 630V ones, but they are a bit more difficult to find in 1 uF ( I am using two in parallel for the 2 uF cap ). Actually, in circuit they will be only about 200 to 250V max across them in normal use.
During warm-up when the rectifier filament is hot but the remaining tubes heaters are still warming up, there will be momentarily higher voltages across some of the caps, but not significantly more than 400V.
Cap 28 ( rated 450V ) sees the most voltage because before the 6A7 warms up, the cap is connected directly to the B+ supply through 20K resistor 26 without any voltage drop from tube current. The remaining caps see less voltage because of voltage divider resistors.
Posts: 1,107
Threads: 88
Joined: Jun 2011
City: Tacoma
State, Province, Country: Washington
I've had no problem getting 1uf and even 2.2uf poly caps at 630 volts. I have a good stash of both of those values.
Posts: 56
Threads: 15
Joined: Jan 2013
City: Felton, PA
I guess the only question then is:
Will three 1uf's and one 2uF 630v mylar caps fit in the can?
(This post was last modified: 09-12-2013, 07:56 PM by
hunter2115.)
Posts: 1,114
Threads: 14
Joined: Feb 2013
City: Irvington, NY
Good question. I know five of these 1 uF 400V fit with plenty of room to spare.
http://www.ebay.com/itm/140318808659?ssP...1497.l2649
Posts: 1,107
Threads: 88
Joined: Jun 2011
City: Tacoma
State, Province, Country: Washington
The new mylar (poly) caps are MUCH smaller than those old paper caps. You'll have enough room left in that can to go dancing.
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
Of course you can go for the Solen Fast caps. Non polarized high quality, I get the low value mfd caps from AES.
Jerry
A friend in need is a pest! Bill Slee ca 1970.