Posts: 1,531
Threads: 242
Joined: Sep 2012
City: West Bend, Wisconsin
Greg V.
West Bend, WI
Member WARCI.org
Posts: 7,298
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Nice Job! Look lke an eastern set, most of those stations I can get over here. WCAU is WPHT now as of 10 or so years ago. I don't understand why stations change call signs after many many years. Kinda like us hams the FCC has allowed us the to have call signs which don't necessarily have to be in the call district we are in. It's a bit of annoyance you think the guy is in Calf. but he's next door.
Terry
Posts: 52
Threads: 1
Joined: Mar 2013
City: Minneapolis, MN
Any stray capacitance between the 75 grid cap and the plate of the output tube ( 41, 42, etc.) can cause hi freq audio oscillation. Dress the grid lead away and/or try some shielding.
Posts: 761
Threads: 56
Joined: Jul 2013
City: Kentucky
Beautiful radio. Great job!
The artist formerly known as Puhpow! 8)
Posts: 120
Threads: 10
Joined: Jul 2011
City: Glendale, CA
I've got a 39-30 as well. I have seen some 39-30's with only 1 tube shield, on the 75 tube. For whatever reason, my radio has provisions for two tube shields, on the 75 and the 37. But, when I got it, it only came with only 1 actual tube shield installed, on the 75. Could that be part of your problem?
Tom
Posts: 2,353
Threads: 92
Joined: May 2010
City: Clayton, NC
Bill/Tom: great advice. Funny thing about 75 tubes, the mutual conductance of the triode is only 750 uMhos, and it doesn't take long for it to degrade to the 500 range. In sets where the 75 is the only AF amp before the output tube this can be an issue.
Also: 42 tubes can be noisy after they warm up. Same goes for 6F6 tubes.
Posts: 2,353
Threads: 92
Joined: May 2010
City: Clayton, NC
Posts: 1,531
Threads: 242
Joined: Sep 2012
City: West Bend, Wisconsin
Mine only has one tube shield too over the 75 tube.
Greg V.
West Bend, WI
Member WARCI.org
Posts: 77
Threads: 24
Joined: Nov 2010
City: Oradell, NJ
Quote:It took three #75 tubes until I found a good one that didn't cause a muffled hissing after the set played for about 5 or 10 minutes
That might have been a supersonic parasitic oscillation. A "grid stopper" resistor, around 68K, placed in series with the grid wire right at the top cap of this tube (its grid), should tame those unruly tubes you have. This resistor, in combination with the tube's stray capacitance, acts like a low pass filter to disable the oscillation.
(This post was last modified: 09-20-2013, 04:33 PM by wa2ise.)
Posts: 61
Threads: 2
Joined: Aug 2013
City: Renton, Wa
Real nice looking set--great restoration !
Posts: 1,531
Threads: 242
Joined: Sep 2012
City: West Bend, Wisconsin
Thanks, everyone. The set is working fine now. I think it had a lot to do with shielding around that 75 tube. No more muffled hissing. 
Greg V.
West Bend, WI
Member WARCI.org
Posts: 1,531
Threads: 242
Joined: Sep 2012
City: West Bend, Wisconsin
I really like the rear lighted dial on these 1939's. And, using the "Rebuilding Philco Pilot Lamps" tip found in the tech section ( http://philcoradio.com/tech/lamps.htm ) it no longer flickers on and off! 
Greg V.
West Bend, WI
Member WARCI.org
Posts: 481
Threads: 18
Joined: Jan 2013
City: Mesa, AZ
Still love those wine flavored buttons! 
Posts: 4,865
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA
Another thing to watch for on a 75 tube, or any other glass tube with a grid cap, is the solder joint on the grid cap giving out. Also the clip on the end of the grid lead can have problems, the solder joint going bad or the wire breaking internally.
Regards
Arran
Posts: 825
Threads: 113
Joined: Aug 2012
City: The Villages
State, Province, Country: Florida
Wow. Really great restoration! 
Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org
Users browsing this thread: 1 Guest(s)
|
|
Recent Posts
|
|
The list of my radio & TV collection!
|
| A little light positivity in our feed... To nostalgic retro music...
With English subtitles
My new video on the contin...RadioSvit — 02:14 PM |
|
My Philco 37-116 Restore
|
| Ron and Mike I mentioned a 2 meg resistor not on the schematic. I stumbled on a changes note in Riders that mentioned th...dconant — 12:02 PM |
|
Need Help to ID this radio 11 tube Philco
|
| Here you go:
Your the code 125Radioroslyn — 11:12 AM |
|
My Philco 37-116 Restore
|
| Hi Ron,
Thanks for the input. I think I'm going to call it good enough. It does seem weird I can usually dial in othe...dconant — 08:01 AM |
|
Need Help to ID this radio 11 tube Philco
|
| Welcome,
the radio looks intimating 11 tubes, wish you well.Jimradio — 07:49 AM |
|
462ron
|
| Hi Dan, it’s been 10 years since I restored the electronics on my 37-116 so I’m going on some foggy memories. I remember...462ron — 07:37 AM |
|
Need Help to ID this radio 11 tube Philco
|
| Yes the 16B as morzh pointed out. Specifically its the January 1935 model version of the 16B. There are a couple earli...klondike98 — 11:51 PM |
|
48-482 rear panel help
|
| Welcome to the Phorum, keithchip! How far you take a radio on cabinet restoration is a matter of personal preference. ...GarySP — 11:28 PM |
|
48-482 rear panel help
|
| I've recently finished the internal restoration of a locally purchased Philco 48-482. The cabinet is in ok shape except ...keithchip — 10:28 PM |
|
Need Help to ID this radio 11 tube Philco
|
| Welcome to the Phorum, Ken! Lots of help here for all of your restoration questions. Take care and BE HEALTHY! - Gar...GarySP — 07:59 PM |
|
Who's Online
|
There are currently 547 online users. [Complete List]
» 1 Member(s) | 546 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
