Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Stewart-Warner 950 battery set
#16

                Wasn't using a heat gun. Was using a hotplate and pan.
#17

Strange set. It doesn't follow the schematic, not even the battery version of the schematic. Said schematic shows stage trimmer caps that do not exist. It shows a pair 171's as outputs, when the radio itself calls for 12A's. Also has different voltages than the radio calls for. Also odd for such a set to have a dial light, but, there it is. I discovered a short time ago that some of the lack of volume was due to my A battery being a bit low. Charging it up a bit resulted in good room filling sound, not loud, but certainly adequate.
#18

Hi All;
Brenda Ann, Thanks for the Great Pictures.. Is this set a TRF or is it a superhetrodyne ?? Just Courious..
When I was a mixed up kid, me and a friend would put our hands in molten Wax, and then run arround the Yard to cool it off, and repeat untill we had a creepy looking wax hand.. So, you forgot to run arround the yard to cool it off..
THANK YOU Marty
#19

I was weirder. I guess I was what they call goth nowadays. I used to dip my fingers in kerosene and hold them straight up and light them, this in my mid teens. I had a sort of death wish back then. Teen angst? Sure glad I got over it. I was insufferable for a few years, even to myself. It's a wonder I'm still here.
Icon_smile
#20

You have to be a bit weird to tinker with electrical stuff decades older then you are to begin with. As for the nail thing I was a bit of a pyro when I was a teenager, still am to a degree, good thing I didn't have any black powder around.
Regards
Arran




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 6022 online users. [Complete List]
» 1 Member(s) | 6021 Guest(s)
Avatar

>