Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Beautiful and highly desirable INGRAHAM CABINET!
#1

really what drugs are they on restored ??
http://www.ebay.com/itm/Antique-1939-Eme...233069f423
#2

Half a Mae West with a crack in her ***. Chassis plays Ok but not a great playing set, Emersom had some sleepers but I think with the power cord on this one it could be electrifying.

Paul

Tubetalk1
#3

Yeah...that ballast tube looks like it just came from garbage.
But yeah...for whatever reason these Emersons are collectable.
Don't see why.

Here's from tuberadioland:
http://www.tuberadioland.com/EmersonAX-212_main.html
#4

That's no ballast tube, that's the antenna coil.
#5

Again, as Morzh/Mike knows Emersons are cheap radios in sometimes pretty cabinets. The cabinet on this set looks terrible, someone at some point slobbed lacquer or varnish all over the original flaking finish, then there is that damaged speaker grille. I really don't get the appeal of these, Emerson wasn't the only one to use fancy cabinets on small sets, yet they seem to grab all the glory just because of that tin plate on the back.
Regards
Arran
#6

Sometimes the plate is on the bottom.

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
#7

I don't know how he can describe that as "restored".. it looks like he dunked it in a can of clear poly and called it done. I wonder how bad the insides are?

The artist formerly known as Puhpow! 8)
#8

From the looks of the antenna coil, I don't see how that radio can work. It looks like it has been struck by lightening.
Jerry

A friend in need is a pest!  Bill Slee ca 1970.
#9

I would take one of these, I bet it would play better, not an Ingraham.
http://www.radiomuseum.org/r/emerson_599_120075b.html

AM only but I bet a good player.

Paul

Tubetalk1
#10

Brenda,

You are right, at a closer look it is the antenna coil. Oh, my Gosh! This thing looks like it has been lifted from the ocean floor after 40 years. If it works, I'll be a monkey's uncle.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT-6 antenna connections
Hi Bridcarl +1 on the others.  Pin 6 of the 7C6 is the AVC Diode so it is appropriate that that pin 4 of the coil con...MrFixr55 — 07:30 AM
462ron
Joseph, this is beyond awesome. A lot of thought and engineering went into this and you hit a home run! Now I must save ...462ron — 07:27 AM
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM

[-]
Who's Online
There are currently no members online.

>