Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

edison radio
#1

hey guys
any know where I can get schematic for this
http://jerseyshore.craigslist.org/atq/4126734509.html
sam
#2

Sam, it doesn't appear to be listed in N/A. Jump on that radio! I love the styling and the dual chassis. Looks to be in great shape.

Regards, Jerry

Edit: this link might give you a little more information. Dual 45s!

http://www.radiomuseum.org/r/edison_r4.html

A friend in need is a pest!  Bill Slee ca 1970.
#3

Ah, I know where two of those are near me, but one has a bad power transformer. Not sure if that is an issue with Edison radios, but might be something too look out for. Other than that, they are nice looking radios. If I could, I'd snag both from the guy I know to get a good one.

No matter where you go, there you are.
#4

You lucky people out there in the Midwest and East are in radio heaven. I doubt I could find one of those within a 400 mile radius. Still have many challenges with my Fada 46 that should take me through Winter.
I really don't have room for another console but certainly liking those old TRF sets. Not certain about the Edison but the old TRF sets I have, both don't have disconnects for the speaker or in one case the sub chassis. A real bear to work on them. Took two people to take the electronics out of my Monarch, all three parts hardwired together. Nasty!
Jerry
Regards, Jerry

A friend in need is a pest!  Bill Slee ca 1970.
#5

Sam
Better eat your Wheaties!
Terry
#6

Sam

They are nice TRF's when done. The PP 45's do make it sound good. I have restored two with the Phonograph. The power transformers are weak and tend to have problems. I had to have a new one wound. Replace both power resistors in the amp chassis as they tend to be open. Plenty of room under the chassis to work and place new caps without opening the cans.

Good luck

Skip
#7

That's not that far from me either.
#8

Having an R32 in my wake I can say that they are definitely not the easiest sets in the world to rebuild.

The schematic for an Edison R4 is: http://www.nostalgiaair.org/Resources/839/M0021839.htm

Your schematic is on page 6.

With 3 stages of RF amplification it should be a decent receiver.
#9

I picked it up this morning. The seller was very very negotiable. It is in good shape except for the speaker cone.

Steve
#10

I'm glad you got that Steve. I noticed your posting on the alternate forum.
Regards, Jerry

A friend in need is a pest!  Bill Slee ca 1970.




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A5...MrFixr55 — 06:48 AM
American Bosch Model 802 auto radio
I think it would come under either American Bosch or United American Bosch. American Bosch made sets for the American We...Arran — 05:53 AM
trying to identify this wire type
Thanks to all for the feedback. As Arran said, it is probably an older replacement and yes it has a grid cap so I will ...georgetownjohn — 09:32 PM
trying to identify this wire type
It's possible that the red wire, actually a grid cap lead, is a very old replacement, I can't remember seeing a pre 1939...Arran — 09:18 PM
Gilfillan Brothers Car Radio?
Hi everyone,  Special thanks to Joe Rossi for tracking down this obscure radio and thanks to others who took up the hun...Antipodal — 08:15 PM
trying to identify this wire type
Here's one source for your wire of many. Take care and BE HEALTHY! Gary P.S. Can't get the right color you need? I ...GarySP — 06:40 PM
trying to identify this wire type
...and modern wire of the appropriate gauges and insulation V-rating (300V minimum, usually shown right on the wire) is ...morzh — 05:47 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
I have a question about this radio, is there anyone that has access to this radio that has an intact unmolested speaker ...captainclock1988 — 04:28 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Well what makes me confuse all of those companies is that all three of those companies (Setchell-Carlson, Stromberg-Carl...captainclock1988 — 04:21 PM
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM

[-]
Who's Online
There are currently 7093 online users. [Complete List]
» 1 Member(s) | 7092 Guest(s)
Avatar

>