Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

edison radio
#1

hey guys
any know where I can get schematic for this
http://jerseyshore.craigslist.org/atq/4126734509.html
sam
#2

Sam, it doesn't appear to be listed in N/A. Jump on that radio! I love the styling and the dual chassis. Looks to be in great shape.

Regards, Jerry

Edit: this link might give you a little more information. Dual 45s!

http://www.radiomuseum.org/r/edison_r4.html

A friend in need is a pest!  Bill Slee ca 1970.
#3

Ah, I know where two of those are near me, but one has a bad power transformer. Not sure if that is an issue with Edison radios, but might be something too look out for. Other than that, they are nice looking radios. If I could, I'd snag both from the guy I know to get a good one.

No matter where you go, there you are.
#4

You lucky people out there in the Midwest and East are in radio heaven. I doubt I could find one of those within a 400 mile radius. Still have many challenges with my Fada 46 that should take me through Winter.
I really don't have room for another console but certainly liking those old TRF sets. Not certain about the Edison but the old TRF sets I have, both don't have disconnects for the speaker or in one case the sub chassis. A real bear to work on them. Took two people to take the electronics out of my Monarch, all three parts hardwired together. Nasty!
Jerry
Regards, Jerry

A friend in need is a pest!  Bill Slee ca 1970.
#5

Sam
Better eat your Wheaties!
Terry
#6

Sam

They are nice TRF's when done. The PP 45's do make it sound good. I have restored two with the Phonograph. The power transformers are weak and tend to have problems. I had to have a new one wound. Replace both power resistors in the amp chassis as they tend to be open. Plenty of room under the chassis to work and place new caps without opening the cans.

Good luck

Skip
#7

That's not that far from me either.
#8

Having an R32 in my wake I can say that they are definitely not the easiest sets in the world to rebuild.

The schematic for an Edison R4 is: http://www.nostalgiaair.org/Resources/839/M0021839.htm

Your schematic is on page 6.

With 3 stages of RF amplification it should be a decent receiver.
#9

I picked it up this morning. The seller was very very negotiable. It is in good shape except for the speaker cone.

Steve
#10

I'm glad you got that Steve. I noticed your posting on the alternate forum.
Regards, Jerry

A friend in need is a pest!  Bill Slee ca 1970.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W  1.5k  ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM
Philco 60 Squealing
I have taken out the 2nd IF and found a problem or not. I believe the coils are litz wire. There is a very small strand ...dconant — 02:13 PM
Philco 6K7
I am restoring a Philco 37-60. The am reception is very good, but the shortwave is very weak. Run 6 Philco removes the g...bobbyd1200 — 01:35 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A5...MrFixr55 — 06:48 AM
American Bosch Model 802 auto radio
I think it would come under either American Bosch or United American Bosch. American Bosch made sets for the American We...Arran — 05:53 AM
trying to identify this wire type
Thanks to all for the feedback. As Arran said, it is probably an older replacement and yes it has a grid cap so I will ...georgetownjohn — 09:32 PM
trying to identify this wire type
It's possible that the red wire, actually a grid cap lead, is a very old replacement, I can't remember seeing a pre 1939...Arran — 09:18 PM

[-]
Who's Online
There are currently 5292 online users. [Complete List]
» 1 Member(s) | 5291 Guest(s)
Avatar

>