Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Restoring a 39-7
#16

I prefer to keep rubber and wires separate. Icon_lol
#17

Thanks, I'll see if my local electronics shop has any...

Edit:

No luck. I have to go to the Internet. Any decent sources for these? I cannot locate any 6000pF caps, only 4700pF.

So what can I do? 4700 is enough, 10000 too much, or should I wire 3 2200's in parallel (I'd rather not tempt the fates of MTBF this way)?

Also there is one other silver mica capacitor in there - it's part 6A on the schematic. The problem is it's listed as a 20mfd device and there's no way this is 20mfd, it's just way too small. Elsewhere on the schematic it's listed as 20mmfd, which makes a lot more sense for this type of capacitor.
#18

It sings again!

After putting up with the repaired speaker that tended to muddle the sound and distort at medium-high volumes, I decided to take a closer look

The speaker was slowly disintegrating - small cracks were developing, and the most careful light touch caused the cone to split.

So I had the speaker reconed.

It's now a whole different radio. Plays loud, tight, and clear at all volumes.

I probably put more money I to this than I should, but it would have been a pity to leave it in such poor condition.

   
#19

Speaker looks very nice. Who did you send it to for reconing?
#20

The Speaker Shop:

http://thespeakershop.com
#21

Nice set! You've got the delux model with the brass escutcheon around the dial. Many years ago I had the chairside version of that set. Wish I hadn't sold it! Good player and very sensitive too.
Terry
#22

Actually, this one doesn't. It's pretty plain. I have a nearly identical model with the preset tuning buttons and the brass escutcheon though. You are right about the play quality and sensitivity though. A solid little radio. The guy who had it before me wrote 38-12 on the chassis, but it is a 39-6 as far as I can tell.

Edit: no, it isn't, it *is* a 38-12 chassis. Just double-checked the schematic. Someone put a dial from a 39-6 on it and stuck it in a 39-6 cabinet. >:-(

Aw crap! Just noticed I posted about the the speaker in my 39-7 thread. At least the 39-7 is a real one.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Restoring Philco 37-604C
Hello mike, My Stand also has some very minor rust too and mine is used inside my heated house . Sincerely Richardradiorich — 11:02 PM
Philco 10 car radio head key
Hi Keandkafu, In general, the Key Code usually has nothing to do with the brand of key, but is a code for how the not...MrFixr55 — 10:37 PM
Radiola 18 Amplifier & PS
If the 2.25V winding is not being used, the center tap wire can be insulated by taping off.  If the 5V filament winding ...MrFixr55 — 07:33 PM
Hippo 46-420 Schematic doesn't match parts list.
Here you have the part in the sch with values. I am not sure what else is needed.morzh — 02:56 PM
Restoring Philco 37-604C
Ron Here are the two of my jigs side by side. They have been with me about the same time (a couple of month differenc...morzh — 02:05 PM
Kurt P
Terry, gotcha, thanks for the clarification.  That’s probably why the speaker seems shorted.  Assuming the OT/FC/speaker...Kurt P — 10:59 AM
Radiola 18 Amplifier & PS
I have the 2.25V and 2.5V information confused, and must look more carefully at the schematic and Hammond transformer in...TN Allen — 10:24 AM
Radiola 18 Amplifier & PS
Thank you for the information, it all helps, although understanding some of it takes time. One reason for doing the PS a...TN Allen — 09:42 AM
462ron
Hi Mike, the radio is coming along nicely but wow, you must have some serious moisture in your shop judging by the amoun...462ron — 06:29 AM
Restoring Philco 37-604C
Have rebuilt the can. The can had 4 caps in it, 2x16uF, 10uF and 8uF. I used a 15uF as the first cap, 22uF and 10uF ...morzh — 09:38 PM

[-]
Who's Online
There are currently no members online.

>