1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco ventilator
Howard R Stricklin
Member
***
Posts: 62
Threads: 9
Joined: Dec 2008
City: loogootee indiana
#16

10-23-2013, 08:15 PM
looking good


Attached Files Image(s)
   
Find
Howard R Stricklin
Member
***
Posts: 62
Threads: 9
Joined: Dec 2008
City: loogootee indiana
#17

10-23-2013, 08:18 PM
red lacquer finish .


Attached Files Image(s)
   
Find
Howard R Stricklin
Member
***
Posts: 62
Threads: 9
Joined: Dec 2008
City: loogootee indiana
#18

10-23-2013, 08:21 PM
new bushings and felt oilers and rivets .


Attached Files Image(s)
   
(This post was last modified: 10-23-2013, 08:22 PM by Howard R Stricklin.)
Find
Howard R Stricklin
Member
***
Posts: 62
Threads: 9
Joined: Dec 2008
City: loogootee indiana
#19

10-23-2013, 08:26 PM
the rubber mounts were suppose to be the same size on both ends but one cap end was a good bit smaller ..an old leather belt solved the problem .


Attached Files Image(s)
   
(This post was last modified: 10-23-2013, 08:27 PM by Howard R Stricklin.)
Find
Howard R Stricklin
Member
***
Posts: 62
Threads: 9
Joined: Dec 2008
City: loogootee indiana
#20

10-23-2013, 08:30 PM
new head wires and drummed sanded the stator with 220 .


Attached Files Image(s)
   
Find
Howard R Stricklin
Member
***
Posts: 62
Threads: 9
Joined: Dec 2008
City: loogootee indiana
#21

10-23-2013, 08:33 PM
ready to go back into the box .


Attached Files Image(s)
   
(This post was last modified: 10-24-2013, 12:21 AM by Howard R Stricklin.)
Find
Arran
Phorum Expert
*****
Posts: 4,707
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
#22

10-26-2013, 12:45 AM
It's up to you of course but I think that some medium walnut, dye based, toner would even out the lighter walnut veneered portions of the cabinet. Nice work on the motor repairs by the way, and fixing the broken grill bars in the front.
Regards
Arran
Find
Howard R Stricklin
Member
***
Posts: 62
Threads: 9
Joined: Dec 2008
City: loogootee indiana
#23

10-28-2013, 02:23 PM
http://youtu.be/UnOULsnYlmQ
Find
Howard R Stricklin
Member
***
Posts: 62
Threads: 9
Joined: Dec 2008
City: loogootee indiana
#24

10-28-2013, 04:01 PM
......


Attached Files Image(s)
   
Find
« Next Oldest | Next Newest »




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Usually a wave trap is for keeping IF signals from entering the antenna and from leaving the antenna. You feed an IF sig...RodB — 09:30 PM
Philco 60 Squealing
I just peaked it for the best signal at 600. NULL it for IF frequency, originally it would have been null for 500kh...Chas — 08:05 PM
Philco 60 Squealing
Wavetrap no longer matters.morzh — 05:19 PM
Philco 60 Squealing
Rod, I had checked out your suggestions but did not help. I did solder the ground rivets to the chassis as Chas suggeste...dconant — 04:52 PM
37-690 Bass Choke Replacement
Yeah, I know, Mouser and Digikey don't have "big iron" components. For some reason Philco was messing with the...Radiodial — 04:25 PM
37-690 Bass Choke Replacement
Yes, I just had to deal with that while repairing the 37-604 Philco. Exactly that value choke was gone. And the current ...morzh — 03:52 PM
37-690 Bass Choke Replacement
Ah, now where to find one. I've into this before on smaller sets, I now recall. Hammond makes one that is only rated...Radiodial — 03:27 PM
Philco 38-7 Speaker
Ask the admins to put them together. As for the renaming, while inside the thread, you simply press "New reply&quo...morzh — 02:23 PM
37-690 Bass Choke Replacement
This is the parts catalog. 32-7528 choke is 65H, 10mA, 2,250 Ohm inductance. Find a suitable one.morzh — 02:18 PM
37-690 Bass Choke Replacement
While troubleshooting the no bass amplification issue, I think I found the culprit. The choke #104 is reading 164K ohms....Radiodial — 01:42 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration