Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Front end variable Capacitor Function?
#1

Hello,

I just bought a model 86 and had posted a request in the cabinet section a few days ago. I got looking at the schematic for this one and there is a strange circuit at the front end which I've never seen before. The schematic shows some kind of variable cap with a line going into the side of the variable cap (?!?).

When I look at the variable cap, I see that when I turn the knob fully CCW the rotor plates hit a tab of metal that acts as a switch I think.

I have not taken apart that section of the radio yet to have a closer look but was wondering if someone might have some info on this setup.

The schematic is a bit confusing on this.

Have started re-capping the chassis, also tested the tubes, found one weak 226 and a very bad 71A output tube. Rest are good. Par for the course...

I should post a picture of my collection of 5 PT-6 Radios that I've collected over the years in case anyone is interested.

The PT-6 was the first old radio I ever bought back in the mid-70's for $5.00 at a garage sale when I was about 15 yrs old. Ever since I've been snagging them when I see them. Great looking radios!

Herb S., Ithaca NY, new member to the Phorum
#2

What cap are you referring to on this schematic ? http://www.philcoradio.com/tech/images/86.jpg
#3

I think he means position #4 cap.
#4

Bob, that would be #4 on the grid of the first RF amp.

Thanks,

Herb S.
#5

He appears to be referring to adjustable capacitor (4) on the schematic.

That capacitor serves two functions. In normal use, it is a fine tuning control that helps you tune in stations with the greatest volume.

On very strong local stations, it is also designed to be turned until it clicks, at which point the volume drops appreciably by shorting the grid of the first RF tube to ground, reducing the set's gain considerably. So it is not only a fine tuning control, but also a crude local-distance switch.

--
Ron Ramirez
Ferdinand IN
#6

Ron,

OK so it shorts the grid to ground. So I presume the signal then makes it through to the 2nd RF tube via the neutralizing cap?

Herb
#7

Neutralizing cap (5), yes.

--
Ron Ramirez
Ferdinand IN
#8

Ron,

OK, thanks! I still have not inspected the chassis in
that area so now it should make sense to me
when I do so.

One other strange thing I noticed about this radio
is that the RC parts #7,#12, and #17 appear to be
fed the B+ from the opposite end of the string
compared to the schematic!

The schematic shows the B+ coming in at point "D"
which is also the feed to the output transformer
primary.

My chassis was wired so the B+ comes in at the first
RF tube and then daisy chains to 2nd RF, then 3rd RF
then the transformer primary!

Strange. This was all original wiring I'm sure also.
I am wondering when I re-do this that I should make
it like the schematic ?

Herb S.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently 1999 online users. [Complete List]
» 1 Member(s) | 1998 Guest(s)
Avatar

>