1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Block capacitor ID help!
37silverstreak
Senior Member
****
Posts: 299
Threads: 107
Joined: Mar 2011
City: Sheboygan Falls,Wisconsin
#1

12-12-2013, 11:04 PM
Does anyone know what the value is for block cap 7296-B? I can't seem to find it listed on chucks site. It's strange as this cap appears to be an original but is not listed in the parts list for my early version 91. the cap is in the same physical location as part 57 which shows as .18 mfd. but that cap is a totally different number. Any help would be greatly appreciated.thanks!
Kevin
Find
klondike98
Phorum Moderator
******
Posts: 5,088
Threads: 270
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#2

12-12-2013, 11:33 PM
See the data sheet Ron has posted at http://www.philcoradio.com/tech/blocks.htm and http://www.philcoradio.com/tech/images/bakelite.pdf

7296-B was replaced by 7296-SU which is a 0.002 uF cap between lugs 1 & 3 and lug 1 is not grounded. rated @ 1000v
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
radiohenry
Senior Member
****
Posts: 496
Threads: 15
Joined: Mar 2013
City: Weymouth Ma
#3

12-12-2013, 11:47 PM
The 7296-b was 0.002 uf.
Henry
Find
« Next Oldest | Next Newest »




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration