1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Cap list for 40-190?
AJboy123
Member
***
Posts: 89
Threads: 25
Joined: Apr 2013
City: Cleveland, OH
#1

12-29-2013, 01:48 PM
Anyone have a cap list for a 40-190? I've finally gotten around to recapping it but I can't find my SAMs on it
Find
jontz
Member
***
Posts: 157
Threads: 7
Joined: Feb 2013
City: Osceola, IN
#2

12-29-2013, 02:13 PM
Full schematic can be found here:

http://www.nostalgiaair.org/Resources/339/M0013339.htm
Find
DeckApe
Senior Member
****
Posts: 438
Threads: 15
Joined: Jul 2008
City: Anacortes, WA
#3

12-30-2013, 08:20 PM
Or a nice clean copy plus all available service data can be ordered from Chuck Schwark for $7. I recommend this. Icon_thumbup
(This post was last modified: 12-30-2013, 08:20 PM by DeckApe.)
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#4

12-30-2013, 08:57 PM
FYI Sam's only goes back to 1946. Your Philco wouldn't be in it.
Terry
Find
klondike98
Phorum Moderator
******
Posts: 5,088
Threads: 270
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#5

12-30-2013, 11:00 PM
...and service bulletin #323 for this radio can be found here: http://www.audiophool.com/Philco.html
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM

[-]
Who's Online
There are currently 5055 online users. [Complete List]
» 1 Member(s) | 5054 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration