Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

#1

any one know what grillclothe is o.e. on this?
thanks,phil
pic here isn't clear enough for me.
#2

anybody?
#3

Do you mean 19LZ?

That cloth is UNOBTAINIUM. A reasonable substitute is Pattern #40 from Radio Grille Cloth Headquarters.

http://www.grillecloth.com/

--
Ron Ramirez
Ferdinand IN
#4

yep,my bad,i have corrected,thanks ron,you saved me again!are you talking about the generic console pattern? just making sure.
phil
#5

Yup, a generic console pattern.

When you go to the Radio Grille Cloth Headquarters site and click on "See the gallery of 40 patterns" link, it brings up a Flash picture showing thumbnails of grille cloth patterns. Page 2, number 24, Pattern 40 is what you want.

--
Ron Ramirez
Ferdinand IN
#6

that's the one i saw,just making sure. i managed to snag the radio local,almost spotless except the cloth,$130!sweet!!!
#7

Awesome.

19LZ sets are slowly coming out of the woodwork, it seems. Apparently Philco made more of these than the identical 19LZX, which included a separate speaker cabinet, and the 91RX, which used a 91 chassis in the same chairside cabinet, along with a separate speaker cabinet.

I am fortunate to own both a 91RX and 19LZ, along with a now complete 19TX. I acquired the 19TX radio unit (which is a small, compact tabletop unit with a handle on top) about 20 years ago, cheap. Barry Jones did his usual excellent work on its cabinet. Early this year, I managed to acquire the nearly impossible to find speaker cabinet for it, so I'm a happy camper. Now to find time to restore the chassis. Icon_confused

--
Ron Ramirez
Ferdinand IN




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM

[-]
Who's Online
There are currently no members online.

>