Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco table top
#1

I am looking for a small table top for restoration.Noticed, that many of them have a a plastic (or bakelite) frame around the dial and speaker being deformed, possible from heat.Are those pieces in any way restorable by using some heat source or some other way? Even perfectly restored radio will look awful with such warped piece . Thanks.
#2

You must be referring to one of the following Philcos which have an escutcheon/grille made of Tenite, which I also call "The Incredible Shrinking Plastic":

41-81T, 41-85T, 41-221C, 41-221CI, 41-226C, 41-841T, 41-842T, 41-843T, 41-844T, 41-851T, 42-842T, 42-843T, 42-844T, 42-853T, 42-854T, 42-PT94, 42-PT95.

These all share the same escutcheon/grille, although the colors vary. Most are swirled brown; one is solid brown (41-226C), two are ivory (41-221CI, 42-PT95).

You can see these models on the following pages:
http://www.philcoradio.com/gallery/1941a.htm
http://www.philcoradio.com/gallery/1941b.htm
http://www.philcoradio.com/gallery/1942a.htm

Philco made two models after the war that use the same grille, but in ivory only:
47-204 - http://www.philcoradio.com/gallery/1947.htm#b
48-206 - http://www.philcoradio.com/gallery/1948a.htm#f

The 47-204 and 48-206 grilles were made of an improved version of the plastic that has not shrunk or warped over the decades as have the grilles from the prewar Philco models.

I tried to get the two guys who are well known in the hobby for making reproduction plastic parts for radios to reproduce this grille since it is used on so many Philco models including the very popular 41-226C "Sled", but they both said no. Now, Phorum member OldRestorer is looking for a 47-204 or 48-206 for a grille to attempt to reproduce.

I have a 47-204 grille somewhere, but it has been temporarily lost in my recent move. I'll find it eventually, probably when I am looking for something else (which is usually how it goes, at least with me).

Now, after all that verbiage, to answer your question about heat: Heat has been used, with varying success, on various Philco Tenite parts, notably the dials on Mystery Control remotes:
http://www.philcoradio.com/tech/myscon.htm

But it could cause more harm than good. Of course, it's worth a try...what do you have to lose other than a badly warped Tenite part?

--
Ron Ramirez
Ferdinand IN
#3

I have a mid to late 30's Stromberg-Carlson with a shrunken plastic face piece. I wondered how it ever got that way. Sounds like it is made of Tenite then from what I just read.

Mine is not warped, it is just too small now for the cutout in the cabinet!

Herb S.
Ithaca NY
#4

I have a couple like that Herb. Is there a screw/hole in the center top?
I spread mine apart and fabricated a hole-plug for the center.

Tim
#5

I will have to look at it again more closely. As I remember it is a solid ring like shape (square-ish).

Herb S.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently 2229 online users. [Complete List]
» 2 Member(s) | 2227 Guest(s)
AvatarAvatar

>