Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

70/90 knobs
#1

I thought both of them have big rosette for tuning, two small rosettes for tone and volume and small conical for power switch.

Now, my 70 came with 3 small conicals (Philco knobs) for all other than the tuning (proper big rosette).

I also saw images online with the same arrangement.

And, to finalize, that poor Philco 70 which I found for Brenda also has 3 small cone-shaped knobs. (link below)
I honestly don't think someone replaced them as part of restoration effort with this one.

So, were there different arrangements?

http://www.ebay.com/itm/antique-philco-r...4d18e16877
#2

I have a first version with original knobs with 1 medium for tuning and 3 small for vol, tone, on/off. I also have a second version with the brass bezel and it has the large for tuning, medium for tone and volume, and small for off/on like on a 71b
#3

I suspect there were variations...Icon_smile
#4

FWIW, Mr. Philco said at the Atlanta SARS meet that the 70 used three small rosette (conical?) and one medium. Similar to the beat up one listed on ebay.
#5

The one I have is one large rosette for tuning (I am not even sure how a medium which is for volume/tone/switch would fit a larger shaft) and three small conicals.
#6

Both of mine have the same shaft size for all 4 controls.
#7

You are right, they are indeed the same size. It seemed like it was not, maybe due to the size of the knob.
#8

Would not be surprised if Philco exercised a degree of liberty in determining what variety of knob went on what control.

My 70 has the large rosette for tuning, medium rosette for vol and tone, and small rosette for on/off.
#9

This is the most popular option I think, this is why I was thinking my was off until I saw a few others like that.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 4822 online users. [Complete List]
» 2 Member(s) | 4820 Guest(s)
AvatarAvatar

>